Need help?Do you have a question about the Dormakaba Muto Premium XL150 and is the answer not in the manual?
Provides general information, intended use, and glass requirements for the sliding door system.
Details glass type suitability, hardware compatibility, movement speed, and force limitations for installation.
Specifies use for dry indoor areas and requires manual, slow opening and closing operations only.
Outlines requirements for substructure, wall load bearing, fastener sizing, and glass component clearance.
Specifies tempered glass standards, flat uncoated clamping areas, and the avoidance of damaged edges.
Emphasizes two-person installation and the necessity of protective gear due to crushing hazards from glass.
Explains the meaning of CAUTION, WARNING, and TIPS symbols used within safety and installation contexts.
Provides guidelines for replacing parts, cleaning hardware, and performing regular checks for smooth operation.
Instructs on proper disposal methods in accordance with local, state, and national regulations.
Details required adhesive products, application tools, and handling timeframes for tempered laminate glass.
Provides an overview of all components required for the correct installation of the fixed panel system.
Details the process of cutting and adhering the adhesive gasket to the track for proper sealing.
Guides on aligning, securing, and leveling the sidelite section profile to the track and mounting surface.
Specifies key dimensional measurements for sidelite glass placement and track mounting configurations.
Covers U-channel installation, including gasket orientation, securing to floor, and profile alignment.
Details steps for placing setting blocks, preparing the U-channel, and inserting the sidelite glass.
Explains how to cut the sidelite gasket to size and press it correctly between the glass and the profile.
Provides instructions on inserting and securing cover clips into the track at recommended intervals.
Guides on measuring, cutting, and snapping view protection clips onto the cover for stability.
Details the installation process for cover spacers, including placement and tightening at track ends.
Covers securing the cover to clips and snapping the view protection profile into place for a finished look.
Instructs on snapping end caps into the cover, sidelite profile, and U-channel for a clean finish.
Provides general information, intended use, and glass requirements for the sliding door system.
Details glass type suitability, hardware compatibility, movement speed, and force limitations for installation.
Specifies use for dry indoor areas and requires manual, slow opening and closing operations only.
Outlines requirements for substructure, wall load bearing, fastener sizing, and glass component clearance.
Specifies tempered glass standards, flat uncoated clamping areas, and the avoidance of damaged edges.
Emphasizes two-person installation and the necessity of protective gear due to crushing hazards from glass.
Explains the meaning of CAUTION, WARNING, and TIPS symbols used within safety and installation contexts.
Provides guidelines for replacing parts, cleaning hardware, and performing regular checks for smooth operation.
Instructs on proper disposal methods in accordance with local, state, and national regulations.
Details required adhesive products, application tools, and handling timeframes for tempered laminate glass.
Provides an overview of all components required for the correct installation of the fixed panel system.
Details the process of cutting and adhering the adhesive gasket to the track for proper sealing.
Guides on aligning, securing, and leveling the sidelite section profile to the track and mounting surface.
Specifies key dimensional measurements for sidelite glass placement and track mounting configurations.
Covers U-channel installation, including gasket orientation, securing to floor, and profile alignment.
Details steps for placing setting blocks, preparing the U-channel, and inserting the sidelite glass.
Explains how to cut the sidelite gasket to size and press it correctly between the glass and the profile.
Provides instructions on inserting and securing cover clips into the track at recommended intervals.
Guides on measuring, cutting, and snapping view protection clips onto the cover for stability.
Details the installation process for cover spacers, including placement and tightening at track ends.
Covers securing the cover to clips and snapping the view protection profile into place for a finished look.
Instructs on snapping end caps into the cover, sidelite profile, and U-channel for a clean finish.
General| System type | Automatic sliding door system |
|---|---|
| Door weight | Up to 150 kg |
| Track length | Up to 6000 mm |
| Power Supply | 230 V AC, 50/60 Hz |
| Material | Aluminum |
| Manual Operation | Yes |
To Next Page
