DoubleTake MAX 5 User Manual

IMPORTANT: Do not fully tighten hardware until instructed.
Read through all instructions before beginning installation.
MAX 5 SEAT INSTALLATION
TABLE OF CONTENTS:
Section 1 - Prepare Car for Installation
Section 2 - Seat Back Support Installation
Section 3 - Armrest Installation
Section 4 - Footrest Supports and Bumper Angle Installation
Section 5 - Rear Seat Mounting
Section 6 - Cushion Installation
Section 7 - Footrest, Safety Bar and Cup Holders Installation
Sold Separately
Chair Holder Easy Access Steps Drop-in Cargo Bed Golf Bag Holder Soft Cargo Carrier Storage Bin Trailer Hitch
OPTIONAL MAX 5 ACCESSORIES
PREPARE CAR FOR INSTALLATION
SECTION 1
Remove the following items to prepare the car for Rear Seat Kit Installation:
• Top
• Top Supports/Drain Tubes
• Bench Back Cushion
• Bag Rack Assembly
NOTE: Save and separate factory hardware for later use.
CAR PREPARATION
1:1
CAT-4: Max5 Rear Seat Kit / May 18, 2018 www.DoubleTakeGolfCar.com
MULTI–FUNCTION REAR SEAT
TM
Supplied hardware has been illustrated at a 1:1 scale for the
ability to verify required lengths quickly and easily. Simply place
the hardware on top of the illustration to ensure you are using
the correct item and measurement.
SCALE HARDWARE GUIDE
• If you are installing a Storage Bin and decide to release the Storage Lid from the Seat Base before installing the
Seat Base and Seat Back Cushion onto the Car, do not try to open the Lid past 90°. Doing so may place too much
stress on the Lid Hinge possibly causing failure.
• Once the Seat Base and Seat Back Cushion are installed on the Car, the Seat Back Cushion acts as a stop for the
Lid protecting the Lid Hinge from hyper-extension.
• As a precaution, we recommend installing the Storage Lid Latch only after the Seat is fully installed on the Car.
DO NOT PUSH OR FORCE THE LID PAST 90° BEFORE SEAT BASE & SEAT BACK CUSHION ARE INSTALLED ON THE CAR

DoubleTake MAX 5 Specifications

General

Brand	DoubleTake
Model	MAX 5
Category	Automobile Accessories
Language	English

Summary

SECTION 1 - PREPARE CAR FOR INSTALLATION

1:1 CAR PREPARATION

Steps to prepare the golf car by removing existing components for rear seat kit installation.

SECTION 2 - SEAT BACK SUPPORT INSTALLATION

2:1 POSITION AND INSTALL SEAT BACK SUPPORTS

Instructions for positioning and installing the seat back support structures onto the golf car.

SECTION 3 - ARMREST INSTALLATION

3:1 ARMREST PREPARATION

Steps to prepare the armrests by inserting threaded studs before installation.

3:2 INSERT ARMRESTS IN BASE

Guide for inserting the prepared armrests into the seat base.

3:3 SECURE ARMRESTS

Instructions for securely attaching the installed armrests.

SECTION 4 - FOOTREST SUPPORTS AND BUMPER ANGLE INSTALLATION

4:1 POSITION SEAT BASE

Instructions for positioning the seat base for assembly.

4:2 INSTALL BUMPER ANGLE

Steps for attaching the bumper angle components to the car.

SECTION 5 - REAR SEAT MOUNTING

4:3 INSTALL REAR SEAT KIT BRACKETS

Instructions for installing the rear seat kit mounting brackets.

5:1 ATTACH REAR SEAT KIT TO SEAT BACK SUPPORTS

Steps for attaching the rear seat kit base to the seat back supports.

5:2 MOUNT BUMPER ANGLE TO CAR

Instructions for mounting the bumper angle to the golf car.

SECTION 6 - CUSHION INSTALLATION

6:1 SEAT BOTTOM CUSHION INSTALLATION

Guide for installing the seat bottom cushion using temporary studs and screws.

6:2 SEAT BACK CUSHION INSTALLATION

Reference to separate instructions for installing the seat back cushion.

SECTION 7 - FOOTREST, SAFETY BAR AND CUP HOLDERS INSTALLATION

7:1 FOOTREST INSTALLATION

Instructions for installing the footrest assembly.

7:2 SAFETY BAR INSTALLATION

Steps for installing the safety bar.

7:3 CUP HOLDER INSTALLATION

Instructions for installing the cup holders.