Dräger drager X-dock 5300

Other manuals for Dräger drager X-dock 5300

Questions and Answers:

C
Charles MooneySep 3, 2025
What to do if Dräger Docking Station shows module not found error?
- M
  Matthew HoltSep 3, 2025
  The 'Module not found' or 'Wrong (incompatible) SW version' error message on the Dräger Docking Station can occur if a master is connected to modules with different software versions. In this case, a firmware update has to be performed via the master, even if the most current firmware is already installed on the master. Also, check whether all connections are correctly connected and screwed tight, because the electrical connection may be faulty.
J
Jessica GarciaSep 1, 2025
What to do if Dräger Docking Station alarm element test not carried out?
- S
  Shawn DixonSep 2, 2025
  If the alarm element test is not being carried out on the Dräger Docking Station, external light sources might be interfering with the test. Check for any interfering external light sources and reposition them or the station as needed.
D
Dustin MoralesAug 31, 2025
Why Dräger Docking Station measuring chamber is leaky?
- J
  Justin VanceAug 31, 2025
  A leaky measuring chamber in the Dräger Docking Station may be caused by a dirty instrument and/or module. Clean the instrument and/or module. Alternatively, the seal may be worn and needs replacing.
F
fjonesAug 29, 2025
What to do if Dräger Docking Station touchscreen does not respond?
- M
  Monica HerringAug 29, 2025
  If the Dräger Docking Station touchscreen isn't responding or has limited response, it might not be calibrated correctly anymore. Recalibrate the touchscreen.
T
Thomas SimmonsAug 27, 2025
What to do if Dräger Docking Station gas monitor not detected?
- M
  Mrs. Lori WilcoxAug 28, 2025
  If a gas monitor isn't being detected by the Dräger Docking Station, consider the following: * The module might be dirty: Clean the module. * The instrument might be dirty: Clean the instrument. * The gas monitor SW version might be out of date: Update the gas monitor SW. If the issue persists, contact DrägerService as the module may be defective.
M
Melinda GriffinAug 27, 2025
What to do if Dräger Docking Station does not recognize USB storage device?
- D
  danielle33Aug 27, 2025
  The formatting of USB storage devices varies, depending on the manufacturer. This applies to the file system (e.g. FAT32 or NTFS) as well as the partitioning. Dräger recommends using FAT32 and a partitioning that contains partitioning tables (USB-ZIP or USB-HDD).
M
moyerwendyAug 25, 2025
What to do if Dräger Docking Station does not start?
- J
  jonathan36Aug 25, 2025
  If your Dräger Docking Station fails to start, it could be due to: * A disconnected power supply: Check all connections to the mains supply, power pack, and the station itself. * A defective power pack: If the connections are secure and the station still doesn't start, the power pack may be defective and require replacement.
S
Scott BakerAug 22, 2025
Why Dräger Docking Station gas monitors do not pass the gas tests?
- W
  wintersstephanieAug 23, 2025
  If gas monitors are failing gas tests on the Dräger Docking Station because test gas isn't reaching the instrument, consider these potential causes: * Incorrect hose connections: Ensure all hose connections are properly connected. * Incorrect station gas configuration: Verify that the station gas configuration is correct. * Empty or closed test gas cylinder: Check the test gas cylinder to ensure it's neither empty nor closed. * Incorrectly set pressure regulator valve: Verify the setting of the pressure regulator valve.