Why is there no display message on my Dräger Safety Equipment handset?
If there is no display message on the Dräger Safety Equipment handset, it indicates no connection between the handset and control unit. Check the connecting cable plugs, disconnect the plug from the handset, and reconnect it. If no messages are still shown, further assistance is needed.
What does 'Control unit mismatch SW-version' mean on Dräger Safety Equipment?
If the Dräger Safety Equipment displays 'Control unit mismatch SW-version', it means the control unit and handset have different software versions. After confirming with the OK button, the software versions can be viewed. Further assistance is needed.
How to fix Dräger Safety Equipment when it says 'Check cable and reconnect'?
If the Dräger Safety Equipment displays 'Check cable and reconnect!', it means there is no connection between the handset and control unit. Check the plugs of the connecting cable and reconnect them to the handset and control unit. If the error message reappears, further assistance is needed.
What to do if Dräger Measuring Instruments displays 'High Temperature / Cool Down Handset'?
If the Dräger Measuring Instruments displays 'High Temperature / Cool Down Handset', it means the temperature of the handset is too high. Detach the handset and take it to a place with a moderate temperature. Then, connect the handset again and perform the test.
What to do if Dräger Measuring Instruments displays 'Low Temperature / Warm Up Handset'?
If the Dräger Measuring Instruments displays 'Low Temperature / Warm Up Handset', it means the temperature of the handset is too low. Detach the handset and take it to a place with a moderate temperature. Then, connect the handset again and perform the test.
What to do if Dräger Measuring Instruments displays 'Blow longer! / Repeat test'?
If the Dräger Measuring Instruments displays 'Blow longer! / Repeat test', it means the breath sample was blown too short. Repeat the test, blowing longer this time.
Why does Dräger Measuring Instruments detect flow during warm-up?
The Dräger Measuring Instruments may detect flow during warm-up if the breath sample has been blown too early. Deliver the breath sample only when requested by the instrument.
What does 'Service required in x days' mean on Dräger Measuring Instruments?
It means that the service interval will expire in x days.
What does 'No readable display texts on handset, but indicator lights functioning' mean on Dräger Measuring Instruments?
If the Dräger Measuring Instruments has no readable display texts on the handset, but the indicator lights are functioning, it could be due to the temperature of the handset being too low. You can perform the test as usual, guided by the indicator lights. Alternatively, detach the handset and take it to a place with a moderate temperature, then connect the handset again.
What does 'Control unit mismatch SW-version "OK"' mean on Dräger Measuring Instruments?
If the Dräger Measuring Instruments displays 'Control unit mismatch SW-version "OK"', it means the control unit and handset have different software versions. After confirming with the OK button, the software versions can be viewed.
Key safety guidelines for product usage and handling, including warnings and compliance requirements.
Explains the meaning of warning, caution, and notice icons used throughout the document.
Visual introduction and identification of the Dräger Interlock 5000 and 7000 components.
Detailed explanation of how the Dräger Interlock 5000/7000 operates, including optional features like camera and GPRS module.
Specifies the designated purpose of the instrument and lists its product approvals.
Guidance on vehicle installation and essential conditions prior to performing a breath alcohol measurement.
Step-by-step instructions for activating the instrument and providing a breath sample.
Explains how to interpret 'Test Passed' and 'Test Failed' results and subsequent actions.
Covers procedures for switching off the vehicle and handling retest requirements during operation.
Introduces the menu system, access to breath tests, service, and device information.
Accessing specific details like handset, control unit, camera, GPS info, and standby times.
Procedures for unlocking the device, using access codes, and managing configuration settings like display and language.
Instructions for instrument calibration, adjustment, and proper cleaning procedures.
Guidelines for product disposal and key technical data including ranges, conditions, and dimensions.
General| Device Category | Alcohol Interlock Device |
|---|---|
| Type | Ignition Interlock Device |
| Purpose | Preventing driving under the influence of alcohol |
| Power Supply | 12/24 VDC |
| Measurement Range | 0.00 to 2.50 mg/L |
| Response/Analysis Time | Typically within seconds |
| Display | LCD or LED screen for user feedback |
| Connectivity | Data download via USB or Bluetooth |
| Sensor Technology | Electrochemical sensor |
| Data Logging | Yes |
| Data Storage | Yes |
| Tamper Resistance | Yes |
| Warm-up time | Typically less than 1 minute |
| Memory | Internal memory for data storage |
| Humidity range | 5 to 95% RH |
| Compliance | Meets national and international standards for BAIIDs |
To Next Page
