What to do if Dräger Measuring Instruments shows 'Handset error / Contact Service !'?
If your Dräger Measuring Instruments displays 'Handset error / Contact Service !', switch the ignition off and on, then repeat the test. If the error message reappears, it indicates a fault on the handset.
What does 'Control unit mismatch SW-version "OK"' mean on Dräger Measuring Instruments?
If the Dräger Measuring Instruments displays 'Control unit mismatch SW-version "OK"', it means the control unit and handset have different software versions. After confirming with the OK button, the software versions can be viewed.
What does 'No readable display texts on handset, but indicator lights functioning' mean on Dräger Measuring Instruments?
If the Dräger Measuring Instruments has no readable display texts on the handset, but the indicator lights are functioning, it could be due to the temperature of the handset being too low. You can perform the test as usual, guided by the indicator lights. Alternatively, detach the handset and take it to a place with a moderate temperature, then connect the handset again.
What does 'Service required in x days' mean on Dräger Measuring Instruments?
It means that the service interval will expire in x days.
What does 'Violation Reset' mean on Dräger Measuring Instruments?
It means too many violations have been detected.
What does 'Service lockout' mean on Dräger Measuring Instruments?
It means service interval expired.
What does 'Control unit error / contact service' mean on Dräger Measuring Instruments?
It means error in control unit.
What to do if the Dräger Safety Equipment test failed?
If the Dräger Safety Equipment displays 'Test failed', it means the measured breath alcohol concentration is above the set limit. Wait at least 15 minutes and repeat the test. If the message appears again, the breath alcohol concentration is still above the limit value.
How to fix Dräger Safety Equipment when it says 'Check cable and reconnect'?
If the Dräger Safety Equipment displays 'Check cable and reconnect!', it means there is no connection between the handset and control unit. Check the plugs of the connecting cable and reconnect them to the handset and control unit. If the error message reappears, further assistance is needed.
What to do if Dräger Measuring Instruments displays 'Test failed'?
If the Dräger Measuring Instruments displays 'Test failed', it means the measured breath alcohol concentration is above the set limit. Wait at least 15 minutes and repeat the test. If the message appears again, the breath alcohol concentration is still above the limit value.
General| Device Category | Alcohol Interlock Device |
|---|---|
| Type | Ignition Interlock Device |
| Purpose | Preventing driving under the influence of alcohol |
| Power Supply | 12/24 VDC |
| Measurement Range | 0.00 to 2.50 mg/L |
| Response/Analysis Time | Typically within seconds |
| Display | LCD or LED screen for user feedback |
| Connectivity | Data download via USB or Bluetooth |
| Sensor Technology | Electrochemical sensor |
| Data Logging | Yes |
| Data Storage | Yes |
| Tamper Resistance | Yes |
| Warm-up time | Typically less than 1 minute |
| Memory | Internal memory for data storage |
| Humidity range | 5 to 95% RH |
| Compliance | Meets national and international standards for BAIIDs |
Key safety guidelines for product usage and handling, including warnings and compliance requirements.
Explains the meaning of warning, caution, and notice icons used throughout the document.
Visual introduction and identification of the Dräger Interlock 5000 and 7000 components.
Detailed explanation of how the Dräger Interlock 5000/7000 operates, including optional features like camera and GPRS module.
Specifies the designated purpose of the instrument and lists its product approvals.
Guidance on vehicle installation and essential conditions prior to performing a breath alcohol measurement.
Step-by-step instructions for activating the instrument and providing a breath sample.
Explains how to interpret 'Test Passed' and 'Test Failed' results and subsequent actions.
Covers procedures for switching off the vehicle and handling retest requirements during operation.
Introduces the menu system, access to breath tests, service, and device information.
Accessing specific details like handset, control unit, camera, GPS info, and standby times.
Procedures for unlocking the device, using access codes, and managing configuration settings like display and language.
Instructions for instrument calibration, adjustment, and proper cleaning procedures.
Guidelines for product disposal and key technical data including ranges, conditions, and dimensions.
To Next Page
