What causes a high yellow flame during burner combustion in Dyna-Glo BF10PTDG-4?
A high yellow flame during burner combustion in your Dyna-Glo heater indicates that there is not enough air. Check the burner for dirt and debris. Also, the gas regulator may be defective, so consider replacing it.
Why is there white powder residue forming within the burner box or on adjacent walls or furniture when using my Dyna-Glo BF10PTDG-4 Heater?
The white powder residue forming within the burner box or on adjacent surfaces when using your Dyna-Glo heater is caused by vapors from furniture polish, wax, carpet cleaners, etc., turning into white powder when heated. Turn off the heater when using these products.
Why is there a slight smoke or odor during initial operation of my Dyna-Glo BF10PTDG-4?
If you notice a slight smoke or odor during the initial operation of your Dyna-Glo heater, this is likely due to residues from the manufacturing process. This problem should stop after a few hours of operation.
Why is my Dyna-Glo BF10PTDG-4 fan making a loud noise? (Select Models)
If the fan on your Dyna-Glo heater (select models) is making a loud noise, the fan housing or blades may be dirty. Also, check if the fan rotation is blocked by wiring or other obstructions. If these are not the causes, the fan may be defective and need to be replaced.
Why is my Dyna-Glo Heater fan not spinning? (Select Models)
If the fan on your Dyna-Glo heater (select models) is not spinning, first verify that the fan is plugged in and set to "MAN" or "AUTO". If it's set to "AUTO", allow 5-10 minutes for the fan to engage. If these steps don't work, the fan motor may be bad and require replacement.
Why is my Dyna-Glo BF10PTDG-4 Heater producing a clicking/ticking noise just after the burner is lit or shut off?
A clicking or ticking noise from your Dyna-Glo heater just after the burner is lit or shut off is typically due to metal expanding while heating or contracting while cooling, which is common in most heaters. If the noise is excessive, contact a qualified service technician.
Why is my Dyna-Glo BF10PTDG-4 Heater producing a whistling noise when the burner is lit?
If your Dyna-Glo heater is producing a whistling noise when the burner is lit, try turning the control knob to the low (1) position and let it warm up for a minute, especially if you turned it to the high (5) position when the burner was cold. Air in the gas line can also cause this; operate the burner until the air is removed from the line. Blocked air passageways on the heater can also be a factor. Also, a dirty or partially clogged burner orifice might be the cause.
What to do if Dyna-Glo BF10PTDG-4 Heater produces unwanted odors?
If your Dyna-Glo heater produces unwanted odors, ventilate the room and stop using odor-causing products while the heater is running, as the heater might be burning vapors from paint, hair spray, or glues. Also, check for gas leaks and correct them. Lastly, if you have a propane/LP model, check and refill the fuel supply tank if it's low.
What causes burner backfiring during combustion in Dyna-Glo Heater?
Burner backfiring during combustion in your Dyna-Glo heater can be caused by a clogged or damaged burner orifice. Alternatively, the burner could be damaged. In some cases, a damaged gas regulator may also be the cause, so consider replacing it.
What to do if my Dyna-Glo BF10PTDG-4 shuts off after a few minutes?
If your Dyna-Glo heater shuts off after running a few minutes, there are several potential causes. First, ensure the gas supply is turned on and the equipment shutoff valve is open. Also, make sure the control knob is fully pressed in while pressing the ignitor, and that the control knob is in the PILOT position. If there is air in the gas lines from installation, continue holding down the control knob and repeat the igniting operation until the air is removed. In case of a depleted propane supply, contact your local propane company. Finally, the ODS/pilot may be clogged, in which case you should clean the ODS/pilot assembly.
To Next Page
General