EasyManua.ls Logo

Dyna-Glo BF10PTDG-4 - User Manual

Dyna-Glo BF10PTDG-4
60 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
VENT-FREE
BLUE FLAME
GAS WALL HEATER
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY
DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
WARNING: This appliance is equipped for
(natural or propane) gas. Field conversion is not
permitted.
- Do not store or use gasoline or other ammable vapors and Iiquids in vicinity of this or
any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the re department.
- Installation and service must be performed by a qualied installer, service agency or the
gas supplier.
This is an unvented gas-red heater. It uses air (oxygen) from the room in which it is
installed. Provisions for adequate combustion and ventilation air must be provided.
Refer to Air For Combustion and Ventilation section on page 8 of this manual.
This appliance may be installed in an aftermarket, permanently located, manufactured (mobile)
home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases.
C US
C US
ANS Z21.11.2-2016
Gas Fired Room Heaters
Volume II - Unvented Room Heaters
IMBF4 - 2019-01-15
MODEL #
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-877-447-4768,
8:30 a.m. – 4:30 p.m., CST, Monday – Friday or
email us at customerservice@ghpgroupinc.com.
Propane
BF10PTDG-4/PMDG-4
BF20PTDG-4/PMDG-4
BF30PTDG-4/PMDG-4
Natural Gas
BF10NTDG-4/NMDG-4
BF20NTDG-4/NMDG-4
BF30NTDG-4/NMDG-4

Table of Contents

Questions and Answers

  • J
    Joshua StewartSep 2, 2025
    What to do if my Dyna-Glo BF10PTDG-4 Heater has a gas odor even when the control knob is in the OFF position?
    • N
      nicole11Sep 2, 2025
      If you smell gas from your Dyna-Glo heater even when the control knob is in the OFF position, there may be a gas leak. Locate and correct all leaks. It is also possible that the control valve is defective, in which case you should contact customer service.
  • P
    Patrick CraigAug 31, 2025
    What to do if my Dyna-Glo Heater has a gas odor during combustion?
    • E
      Erika WilkersonAug 31, 2025
      If you notice a gas odor during combustion with your Dyna-Glo heater, it could be due to foreign matter between the control valve and burner. Take apart the gas tubing and remove any foreign matter. Another possibility is a gas leak, in which case you should locate and correct all leaks.
  • C
    Christopher PettyAug 29, 2025
    Why does my Dyna-Glo BF10PTDG-4 Heater shut off in use (ODS operates)?
    • A
      alexandershafferAug 30, 2025
      If your Dyna-Glo heater shuts off during use while the ODS is operating, it may not be getting enough fresh air, so open a window or door for ventilation. Low line pressure could also be the cause; contact your local gas supplier. Additionally, the ODS/pilot might be partially clogged, so clean it.
  • S
    Sydney WrightAug 28, 2025
    What to do if there is no spark at ODS/pilot when the ignitor is pressed in my Dyna-Glo Heater?
    • K
      Kyle HernandezAug 28, 2025
      If there is no spark at the ODS/pilot when the ignitor is pressed on your Dyna-Glo heater, the ignitor electrode might be positioned wrong or broken, in which case you should replace the ODS. Also, check if the ignitor electrode is not connected to the ignitor cable and replace the ignitor cable if needed. The ignitor cable could be pinched or wet; free it if pinched and keep it dry. If the ignitor cable is damaged, replace it. A bad ignitor or ignition module can also cause this, so replace them if necessary. Finally, a bad battery can be the culprit, so replace it.
  • J
    juanevansAug 26, 2025
    How to fix a Dyna-Glo BF10PTDG-4 Heater with delayed ignition of burner(s)?
    • C
      Crystal MosleyAug 27, 2025
      If your Dyna-Glo heater experiences delayed ignition of the burner(s), the manifold pressure might be too low, contact your gas supplier. Alternatively, the burner orifice may be clogged.
  • R
    Rachel SimsAug 25, 2025
    Why won't the burner(s) light after the ODS/pilot is lit on my Dyna-Glo Heater?
    • L
      Luke RamirezAug 25, 2025
      If the burner(s) on your Dyna-Glo heater do not light after the ODS/pilot is lit, first ensure that the thermostat setting is not too low by turning the thermostat knob to a higher setting. The burner orifice may also be clogged. Insufficient inlet gas pressure could also be the reason; contact your gas supplier.
  • J
    Joshua CainAug 22, 2025
    Why does the ODS/pilot light on my Dyna-Glo BF10PTDG-4 Heater go out when I release the control knob?
    • K
      Karen AndersonAug 23, 2025
      If the ODS/pilot light on your Dyna-Glo heater goes out when you release the control knob, ensure that the control knob is fully pressed in and held for 30-60 seconds after the pilot lights. Also, check that the equipment shutoff valve is fully open. A loose thermocouple connection can also cause this issue; hand-tighten it until snug, then tighten an additional ¼ turn. If the thermocouple is damaged, it should be replaced. Contact customer service if the control valve is damaged. Finally, if the inlet gas pressure is too high, contact your gas supplier to check and adjust it.

Dyna-Glo BF10PTDG-4 Specifications

General IconGeneral
BrandDyna-Glo
ModelBF10PTDG-4
CategoryHeater
LanguageEnglish

Related product manuals