E-FLITE Apprentice S 15e

Questions and Answers

T
Thomas SmithNov 22, 2025
What to do if E-FLITE Apprentice S 15e aircraft will not connect after binding?
- T
  Travis CaldwellNov 22, 2025
  If your E-FLITE Toy aircraft won't connect to the transmitter after binding, consider these possibilities: * The transmitter might be too close to the aircraft. Try moving the transmitter a few feet away, then disconnect and reconnect the flight battery to the aircraft. * There might be interference from metal objects, wireless sources, or other transmitters. Relocate the aircraft and transmitter and try connecting again. * The bind plug might still be installed. Rebind the transmitter to the aircraft and remove the bind plug before cycling power. * The aircraft might be bound to a different model memory. Select the correct model memory on your transmitter. * The flight or transmitter battery charge could be too low. Replace or recharge the batteries. * The transmitter may hav...
W
walshjoshuaAug 27, 2025
How to fix oscillation in E-FLITE Apprentice S 15e?
- J
  John MillerAug 27, 2025
  If your E-FLITE Toy is experiencing oscillation, here are some potential causes and solutions: * Flying over recommended airspeed: Reduce airspeed. * Damaged propeller or spinner: Replace the propeller or spinner. * Imbalanced propeller: Balance the propeller. * Motor vibration: Replace parts or correctly align all parts and tighten fasteners as needed. * Loose receiver: Align and secure the receiver in the fuselage. * Loose aircraft controls: Tighten or otherwise secure parts (servo, arm, linkage, horn, and control surface). * Worn parts: Adjust gain to compensate for parts wear or replace worn parts (especially propeller, pivot points, or servo). * Irregular servo rotation: Replace the servo.
A
Andrew BrownAug 27, 2025
Why is my E-FLITE Apprentice S 15e Toy making extra propeller noise?
- D
  David SantiagoAug 27, 2025
  If your E-FLITE Toy is producing extra propeller noise or vibration, consider these solutions: * Replace any damaged propeller, spinner, collet, or motor parts. * Balance or replace the propeller if it's out of balance. * Tighten the prop nut if it's too loose. * Ensure the spinner is tight and fully seated; if not, tighten it or remove it and turn it 180 degrees.
F
Frank MillerAug 29, 2025
What to do if E-FLITE Apprentice S 15e Toy doesn't respond to throttle?
- R
  Richard SmithAug 29, 2025
  If your E-FLITE Toy aircraft responds to other controls but not to the throttle, check these: * Ensure the throttle is at the lowest position and the throttle trim is not too high. Reset the controls accordingly. * Verify the throttle servo travel is set to 100% or greater. * Check if the throttle channel is reversed and, if so, reverse it on the transmitter. * Confirm that the motor is properly connected to the ESC.
J
Jared LopezAug 30, 2025
Why control surface does not move on E-FLITE Apprentice S 15e Toy?
- J
  Julie SullivanAug 30, 2025
  If a control surface on your E-FLITE Toy isn't moving, consider the following: * Inspect and replace or repair any damaged control surfaces, control horns, linkages, or servos, then adjust the controls. * Check wires and connections for damage or looseness; connect or replace as needed. * Ensure the transmitter is correctly bound or that the correct model is selected; re-bind or select the correct model in the transmitter. * Fully recharge the flight battery if the charge is low. * Replace the ESC if the BEC (Battery Elimination Circuit) is damaged. * Power on the ESC switch if it's off.
J
jeremymurphyNov 21, 2025
Why E-FLITE Apprentice S 15e aircraft will not bind to transmitter?
- A
  Anthony HumphreyNov 21, 2025
  If your E-FLITE Toy aircraft won't bind to the transmitter, there are several potential causes: * The transmitter might be too close to the aircraft. Try moving the transmitter a few feet away, then disconnect and reconnect the flight battery to the aircraft. * There might be interference from metal objects, wireless sources, or other transmitters. Relocate the aircraft and transmitter and try binding again. * The bind plug may not be correctly installed. Ensure it is properly inserted into the bind port before binding. * The flight or transmitter battery charge could be too low. Replace or recharge the batteries. * The bind switch or button may not have been held long enough. Power off the transmitter and repeat the bind process, holding the bind button or switch until the rece...
E
Erin MillerSep 18, 2025
What to do if controls are reversed on my E-FLITE Apprentice S 15e Toy?
- F
  ftaylorSep 22, 2025
  If the controls on your E-FLITE Toy are reversed, it's likely due to reversed transmitter settings. Perform the Control Direction Test and adjust the controls on the transmitter accordingly.
S
scott23Sep 23, 2025
What to do if trim is at extreme and aircraft does not fly straight or level with my E-FLITE Toy?
- G
  Glenda TorresSep 23, 2025
  If the trim is at an extreme setting and your E-FLITE Toy aircraft doesn't fly straight or level, it might be because the trim is not at neutral. If you adjust trim more than 4 clicks, adjust the clevis to mechanically remove trim.
R
Richard FosterSep 12, 2025
What to do if my E-FLITE Apprentice S 15e aircraft will not respond to throttle but responds to other controls?
- J
  juliekingSep 12, 2025
  If your E-FLITE Toy aircraft responds to other controls but not to the throttle, check the following: * Ensure the throttle is at the lowest position and the throttle trim is not too high. Reset the controls accordingly. * Verify that the throttle servo travel is set to 100% or greater. * Confirm that the throttle channel is not reversed. If it is, reverse the throttle channel on the transmitter. * Make sure the motor is properly connected to the ESC.
N
Nicole GoldenSep 5, 2025
What to do if E-FLITE Apprentice S 15e Toy control surfaces do not move after switch on?
- J
  Jeremy BeckerSep 6, 2025
  If the aircraft control surfaces on your E-FLITE Toy do not move after the switch is turned on, it is possible that the aircraft was moving during initialization. Keep the aircraft still during initialization.