Why is there excessive overspray with my Earlex Paint Sprayer?
Excessive overspray from your Earlex Paint Sprayer can occur if the pressure is too high or if you're holding the sprayer too far from the surface. To fix this, turn the output knob clockwise to reduce the pressure and ensure you hold the paint sprayer about 25-30cm (10”-12”) from the surface.
What to do if my Earlex Paint Sprayer motor operates but splutters?
If your Earlex Paint Sprayer motor runs but the spray is spluttering, several factors could be the cause: * The paint container might be almost empty, so refill it. * You may be holding the sprayer at the wrong angle; ensure you hold it correctly. * The liquid could be too thick, in which case you should thin it as recommended. * The regulation control might be incorrectly set; adjust the regulator at the back of the paint sprayer. * The nozzle or valve assembly could be worn; replace the nozzle or valve assembly as needed. * An incorrect nozzle might be fitted; replace the nozzle with the correct size.
What to do if my Earlex Paint Sprayer motor operates, but nothing comes out?
If your Earlex Paint Sprayer's motor is running, but no paint is coming out, the issue is likely a blockage. The nozzle or nozzle valve assembly might be blocked. Clean the nozzle thoroughly with thinners, or with water if you are using water-based paint. Also, clean the nozzle valve assembly thoroughly with thinners.
Why is my Earlex Paint Sprayer dripping from the nozzle?
Paint dripping from the nozzle of your Earlex Paint Sprayer is likely due to a loose nozzle or holding the sprayer at an incorrect angle (more than 45 degrees). Ensure the nozzle is tightened and keep the paint sprayer upright during use.
How to fix no suction feed in my Earlex Paint Sprayer?
If your Earlex Paint Sprayer has no suction feed, it could be due to several reasons. The liquid may be too thick, so thin it as recommended or contact the paint manufacturer. Also, ensure the valve assembly is correctly installed by removing the nozzle and inserting the valve assembly before refitting the nozzle. A blocked paint suction tube and filter assembly can also cause this issue, so clean the filter.
How to troubleshoot an Earlex Paint Sprayer that hums but does not operate?
If your Earlex Paint Sprayer hums but doesn't operate, the piston may be sticking. To resolve this, remove the large knob at the top, pull the nozzle and piston assembly down and back to release it. Insert the metal punch from the spares pack into the cylinder housing and gently tap to eject the seized piston. Clean and lubricate the piston and cylinder before carefully re-assembling in reverse order, remembering to replace the compression spring onto the piston. Ensure no parts are dropped into the main paint sprayer assembly.
Why is my Earlex ASG55 spluttering?
Spluttering from your Earlex Paint Sprayer can occur for several reasons: * The container might be almost empty, so refill it. * You may be holding the spray gun at the wrong angle; adjust accordingly. * The liquid you're spraying could be too thick; thin it as recommended. * The regulation control may be incorrectly set; adjust the regulator at the back of the gun. * The fitted nozzle could be incorrect; replace it with the correct size. * The nozzle might be worn; replace it with part number SG211, SG210, or SG209. * The valve assembly could be worn; replace it with part number SG301.
What to do if my Earlex Paint Sprayer has no suction feed?
If your Earlex Paint Sprayer has no suction feed, it could be due to a few reasons: * The liquid might be too thick. Thin it as recommended by the manufacturer. * The valve assembly might be missing. Remove the nozzle, insert valve assembly part no. SG301, and refit the nozzle. * The paint pickup filter could be blocked. Clean filter accordingly part no. SG240.
How to reduce fogging with my Earlex ASG55 Paint Sprayer?
Excessive fogging with your Earlex Paint Sprayer can be caused by: * Holding the sprayer too far from the surface. Keep the sprayer about 10”-12” (25 - 30cm) from your work. * The pressure being too high. Turn the output knob clockwise to reduce the pressure.
Why is my Earlex Paint Sprayer dripping paint?
Paint dripping from your Earlex Paint Sprayer can occur if: * The nozzle is loose. Tighten it by hand. * You are operating the sprayer at more than a 45-degree angle. Keep the sprayer upright.
Details measured noise and vibration levels according to EN50144-2-7.
Key safety warnings, including injection risk, wet weather, and flammable materials.
Step-by-step guide to initial setup, filling, and starting the paint sprayer.
Instructions on adjusting the material flow and spray pattern using the control knob.
Guidance on optimal nozzle distance, movement speed, and gun angle for even coverage.
Tips for achieving better results, including coat application, object size, and pattern.
Guidance on choosing between 0.6mm and 1.0mm nozzles for different applications.
Essential steps for thoroughly cleaning the paint sprayer after each use.
Information on the 12-month guarantee against faulty manufacture and materials.
General| Power | 550 W |
|---|---|
| Max Pressure | 55 bar |
| Weight | 4.5 kg |
| Hose Length | 5 m |
| Type | Airless |
| Spray Pattern Adjustment | Yes |
| Flow Rate | 1.2 l/min |
To Next Page