EasyManua.ls Logo

EarthWay 2100P Estate User Manual

EarthWay 2100P Estate
8 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
2100P EstatE
Broadcast sPrEadEr
ASSEMBLY and OPERATING INSTRUCTIONS
Lower
Housing Clip
Axle
Bushing
Axle
Bearing
⅛ x ¾”
Cotter Pin
⅛ x 1¾”
Cotter Pin
⅛ x 1¼”
Cotter Pin
#12 x 1¼”
Flat Head Screw
¼-20 x 1¾”
Carriage Bolt
¼-20
Lock Nut
Axle
Washer
Agitator
¼-20
Hex Nut
#10 x ⅝”
Screw
¼-20 x
1¼” Bolt
¼-20 x
1½” Bolt
¼-20 x
2” Bolt
FRAME
IMPELLER
CONTROL
ASSEMBLY
UPPER HANDLE
ASSEMBLY
DRAW BAR
&
BRACE ASSEMBLY
GEARBOX
AXLE
1. Remove and identify all loose parts from carton.
(Qty 4) #31105
#12 X 1¼”
Flat Head Screw
9-2014 Pt.# 52159 PAGE 1
2. Position the Hopper on its top as shown
to the left. Install frame using (4) #12 x
1¼” Flat Head Phillips screws. TIGHTEN
THESE NOW - use care to not over tighten
HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY
; If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The
impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the impeller
plate after each use. Fertilizer stuck on the impeller blades will cause uneven spreading.
; Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds
will change the spread patterns. Wet fertilizer will also change the spread pattern and ow rate. Clean and dry your
spreader thoroughly after each use. Coat all metal surfaces (inside & outside of chassis tubes) with light oil or silicon spray
to help prevent corrosion. Wash between the shut off plate and bottom of the hopper. Do not use powdered materials.
; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS
REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT
SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, Email: tEchsuPPort@Earthway.com
MADE IN THE USA
Warning
Remove agitator when
using Rock Salt to prevent
gearbox damage
Question and Answer IconNeed help?

Do you have a question about the EarthWay 2100P Estate and is the answer not in the manual?

EarthWay 2100P Estate Specifications

General IconGeneral
BrandEarthWay
Model2100P Estate
CategorySpreader
LanguageEnglish

Summary

Helpful Hints for Spreader Operation

Proper Impeller Rotation

Ensure the gearbox front points forward for correct impeller rotation (clockwise).

Initial Assembly Steps

Impeller, Gearbox, and Axle Assembly

Gearbox and Axle Installation

Install gearbox with 'FRONT' pointing forward. Slide axle through gearbox with drive wheel hole positioned correctly.

Final Tightening Procedure

Wheel and Control Assembly Installation

Handle, Calibration, and Agitator Assembly

Calibration Procedure

Ensure shut-off and drop holes are fully open at #30. Adjust control cable/rod for proper calibration.

Operating Instructions

Spreading Operation

Move stop bolt, push spreader, pull control lever. Close holes before stopping movement.

Parts List and Diagram

Agitator Warning

Warning to remove agitator when using rock salt to prevent gearbox damage.

Calibration Techniques

Rod Type Adjustment

Adjust control rod at the pivot bracket to ensure shut-off opens fully at #30.

Cable Type Adjustment

Adjust control cable at the clamp to ensure shut-off opens fully at #30.

Setting Rate and Spread Path Guidance

Estimating a Setting Rate

Use Chart 1 to estimate LBS/1,000 sq ft, then Chart 2 for spreader setting.

Determining Spread Width

Use Chart 3 to evaluate particle size and weight for spread width.

Consistent Walking Speed

Maintain a consistent walking speed of 2-3mph for accurate application rate.

Related product manuals