Eaton Airflex VC 5000 - Mounting Spider and Drum Hub; Shaft Alignment

TABLE 3 - AIR CONNECTIONS FOR VC ELEMENTS
SIZE
II .5vc500
201402
AIR TUBE
WASHER
72x15
72x11
72x11
72x11
72x12
72x12
72x13
72x13
72x13
14VC500 201302
16VC600
201302
2OVC600
201302
24VC650
201286
28VC650
201286
33VC650
201284
37VC650 201284
42VC650 201284
14VC1000
16VCl000
20VC1000
24VC1000
28VCl000
32VCl000
38VCl200
42VC1200
46VC1200
52VC1200
51VC1600
60VC1600
66VC1600
OLD METHOD
CURRENT METHOD
(FLANGED TUBE)
(STRAIGHT TUBE)
201302 72x11
202408 72x11
201302 72x11
201286 72x12
201286 72x12
201286 72x12
201284
72x13
201284 72x13
202081 72x13
202751 72x14
304213 72x14
304213 72x14
2.5.5
Align the element air connections with the pas-
sages in the spider and attach the element to
the spider with the appropriate fasteners. See
Table 1. Make sure the element fully engages
the register in the spider.
A
! Warning:
/ \
Use only the proper grade and number
of fasteners. Using commercial grade
fasteners (Grade 2) in place of Grade 8
fasteners may result in failure of the
fasteners under load, causing personal
injury or equipment damage.
26 .
Installation of Element and Drums
(Dual Wide)
2.6.1
Separate the shafts as
clearances will allow.
far as the bearing
2.6.2
Attach the drum having the female register on
the drum flange to the drum hub with screws
and lockwashers. There are tapped holes in
the drum flange to accept the screws. Make
sure the bore in the drum flange fully engages
the pilot on the drum hub. See Figure 3.
VC 5000
Revised: July, 1995 (PDF format)
2.6.3
2.6.4
2.6.5
9
AIR TUBE
WASHER
412178-02
412324-01
412178-03
412324-02
412178-03 412324-02
412178-03
412324-02
412178-05
412324-03
412178-05
412324-03
412178-06
412324-04
412178-06
412324-04
412178-06
412324-04
412178-03
412324-02
412178-03
412324-02
412178-03
412324-02
412178-05
412324-03
412178-05 412324-03
412178-05 412324-03
412178-06 412324-04
412178-06
412324-04
412178-07
412324-04
412178-08 412324-05
412178-09
412324-05
412178-I8 412324-06
412178-04
412324-06
Disassemble the dual element into two
halves and, noting the orientation of the air
connections, place the element onto the drum
installed in 2.6.2.
Noting the orientation of the flange on the
remaining drum with respect to the air connec-
tions on the remaining element, slide the drum
into the element.
Hoist the element/drum into position, align the
tapped holes in the drum having the male pilot
with the tapped holes in the drum attached to
the drum hub, and attach both drums to the
drum hub with the appropriate fasteners. See
Table 1. Make sure the male pilot fully engages
the female register.
Warning:
Use only the proper grade and number
of fasteners. Using commercial grade
fasteners (Grade 2) in place of Grade 8
fasteners (where called for) may result
in failure of the fasteners under load,
causing personal injury or equipment
damage.
@ Copyright Eaton Corp., 1995. All rights reserved.