Eaton Box 1 - C600 M Wiring Kit Diagrams: C30 CN Off;On 2-Position Selector Switch; Lighting Contactor C30 CN, Off;On 2-Position Selector Switch; C600 M Wiring Kit Diagrams: C30 CN Hand;Off;Auto 3-Position Selector Switch; Lighting Contactor C30 CN, Hand;Off;Auto 3-Position Selector Switch

13
Instructions and Operation P52899
Effective July 2019
Box 1 and Box 2 non-combination enclosed
control and C600M cover control kit wiring
EATON www.eaton.com
C600M wiring kit diagrams—Box 2
LIGHTING CONTACTOR MAGNETICALLY HELD. REF.: OFF/ON 2-POSITION SELECTOR SWITCH RED RUN GRN OFF
XO
NO3
NO4
OPTION FOR RED RUN LIGHT (RED TYPICAL)
1
2
REQUIRED FOR 480V OPTION
CONTROL
MODULE
REFERENCE NOTES BELOW FOR
CONTROL POWER WIRING OPTIONS
1
COVER CONTROL
OPTION SHOWN
DASHED COMPONENTS ARE OPTIONAL
USE AS REQUIRED FOR SELECTED COVER CONTROL OPTIONS
2
2
OX
G
R
A2
A1
A2
A1
~
~
-
+
NO4
NO3
1
2
1
2
X2X1
1
2
1
2
X2
X1
M
M
M
L2
M
OFF
RUN
M
M
BLK/WHT
RED
RED
BLK
WHT
BLK
RED
YLW
RED/BLK
RED
RED
RED/BLK
RED RED
BLK/WHT
RED
RED
RED
2
3
AUX
AUX
OFF
ON
L1 OR SEPARATE CONTROL
L2 OR SEPARATE CONTROL
X2
X2
1
ONOFF
X2
X2
1
CONTROL POWER WIRING NOTES
CAUTION
READ AND FOLLOW INSTRUCTIONS PRIOR TO WIRING OR CONNECTING POWER! THIS PRODUCT
CAN BE FACTORY OR FIELD CONFIGURED FOR MULTIPLE CONTROL MODES OR CONTROL
VOLTAGES. CHECK NAMEPLATE FOR COIL VOLTAGE.
SEPARATE CONTROL POWER
FOR COIL VOLTAGES 120V AND LESS: CONNECT SEPARATE CONTROL LINES TO THE NO. 61
TERMINAL ON THE TOP ADDER AUX. AND TO THE A2 TERMINAL ON THE COIL.
FOR COIL VOLTAGES GREATER THAN 120V: REMOVE WIRE "C2" IF SUPPLIED. IF WIRE "C1" IS
TERMINATED ON L1, DISCONNECT FROM L1. CONNECT SEPARATE CONTROL LINES TO THE "C1"
WIRE OR APPROPRIATE PILOT DEVICE TERMINAL PER DIAGRAM AND TO THE A2 TERMINAL
ON THE COIL.
COMMON CONTROL POWER
FOR COIL VOLTAGES 120V AND LESS: ADD WIRE "C2" IF NOT SUPPLIED. ADD CONNECTOR
BETWEEN L1 TERMINAL AND THE NO. 61 TERMINAL ON THE TOP ADDER AUX. OR APPROPRIATE
PILOT DEVICE TERMINAL PER DIAGRAM.
FOR COIL VOLTAGES GREATER THAN 120V: ADD WIRE "C1" AND "C2" IF NOT SUPPLIED.
LIGHTING CONTACTOR MAGNETICALLY HELD. REF.: HAND/OFF/AUTO 3-POSITION SELECTOR SWITCH RED RUN GRN OFF
0X0
NC1
NC2
0X0
NC1
NC2
OPTION FOR RED RUN LIGHT (RED TYPICAL)
1
2
REQUIRED FOR 480V OPTION
CONTROL
MODULE
FACTORY INSTALLED JUMPER.
CUSTOMER TO DISCONNECT JUMPER FROM NO3 OF AUTO
AND CONNECT REMOTE SWITCH AS SHOWN.
IF NOT DISCONNECTED, "AUTO" WILL OPERATE EQUIVALENTLY TO "HAND".
REMOTE
SWITCH
REFERENCE NOTES BELOW FOR
CONTROL POWER WIRING OPTIONS
DASHED COMPONENTS ARE OPTIONAL
USE AS REQUIRED FOR SELECTED COVER CONTROL OPTIONS
COVER CONTROL
OPTION SHOWN
1
2
2
R
G
XOO
OOX
A2
A1
A2
A1
~
~
-
+
1
2
1
2
X2
X1
X2X1
1
2
1
2
NO4
NO3
NO4
NO3
M
M
L2
M
RUN
OFF
M
M
M
RED
RED
BLK
WHT
RED
RED/BLK
RED
RED
RED/BLK
RED RED
BLK/WHT
BLK/WHT
RED
BLK
YLW
RED
RED
RED
RED
RED
RED
3
AUX
AUX
2
OFF
ON
L1 OR SEPARATE CONTROL
L2 OR SEPARATE CONTROL
X2
X2
1
AUTO
0
HAND
X2
X2
1
CONTROL POWER WIRING NOTES
CAUTION
READ AND FOLLOW INSTRUCTIONS PRIOR TO WIRING OR CONNECTING POWER! THIS PRODUCT
CAN BE FACTORY OR FIELD CONFIGURED FOR MULTIPLE CONTROL MODES OR CONTROL
VOLTAGES. CHECK NAMEPLATE FOR COIL VOLTAGE.
SEPARATE CONTROL POWER
FOR COIL VOLTAGES 120V AND LESS: CONNECT SEPARATE CONTROL LINES TO THE NO. 61
TERMINAL ON THE TOP ADDER AUX. AND TO THE A2 TERMINAL ON THE COIL.
FOR COIL VOLTAGES GREATER THAN 120V: REMOVE WIRE "C2" IF SUPPLIED. IF WIRE "C1" IS
TERMINATED ON L1, DISCONNECT FROM L1. CONNECT SEPARATE CONTROL LINES TO THE "C1"
WIRE OR APPROPRIATE PILOT DEVICE TERMINAL PER DIAGRAM AND TO THE A2 TERMINAL
ON THE COIL.
COMMON CONTROL POWER
FOR COIL VOLTAGES 120V AND LESS: ADD WIRE "C2" IF NOT SUPPLIED. ADD CONNECTOR
BETWEEN L1 TERMINAL AND THE NO. 61 TERMINAL ON THE TOP ADDER AUX. OR APPROPRIATE
PILOT DEVICE TERMINAL PER DIAGRAM.
FOR COIL VOLTAGES GREATER THAN 120V: ADD WIRE "C1" AND "C2" IF NOT SUPPLIED.
ote:N Source drawing reference wiring diagrams 288257.