Eaton Box 1 - C600 M Wiring Kit Diagrams: Rev;Dwn;Up Selector Switch Options; Rev;Off;Fwd or Dwn;Off;Up 3-Position Selector Switch Options

8
Instructions and Operation P52899
Effective July 2019
Box 1 and Box 2 non-combination enclosed
control and C600M cover control kit wiring
EATON www.eaton.com
C600M wiring kit diagrams—Box 1 and Box 2
RED RED
RED
RED
1/L1 OR SEPARATE CONTROL
3/L2 OR SEPARATE CONTROL
_/21/616/22/62
A2
A1
9695
9897
5/14/544/13/53
_/21/617/22/62
A2
A1
3/14/542/13/53NO4 NO3
NO4 NO3
X2X1
X2X1
1
2
1
2
1
2
1
2
5453 5453
6463 6463
A1
9695
9897
A1
X2X1
X2X1
A2
A2
OOX
1/L1
XOO
R
R
R
R
R
F
OL
OL
R
F
R
F
FWD/UP
REV/DWN
F R
F R
F HOLD
OL
OL
R HOLD
FWD/UP
REV/DWN
F PICKUP
R PICKUP
F LATE OPENING
R LATE OPENING
R1
R1
L1
L1
T1 T2
T1 T2
L1
R1
RED
RED
RED
BLK
BLU
RED/BLK
RED/BLK
RED/BLK RED/BLK
REV/OFF/FWD OR DWN/OFF/UP 3-POSITION SELECTOR SWITCH OPTIONS SHOWN: REV/DWN LIGHT AND FWD/UP LIGHT
RED
RED
RED
RED
(BLU IF DC)
RED
(BLU IF DC)
RED
(BLU IF DC)
BLU
BLU
BLU BLU
BLU/WHT
BLU BLU
RED/BLK RED/BLK
RED/BLK
RED/BLK
BLU
BLU
DASHED COMPONENTS ARE OPTIONAL
USE AS REQUIRED FOR SELECTED COVER CONTROL OPTIONS
REFERENCE NOTES BELOW FOR CONTROL POWER WIRING OPTIONS
SEPARATE CONTROL WIRES
1
OPTION FOR RUN LIGHT (RED TYPICAL)
2
REQUIRED FOR 480V OPTION
3
TWO 2NO TOP ADDER AUX INCLUDED FOR ALL COIL VOLTAGES. WHEN
COIL VOLTAGES 120V AND LESS, CONTROL WIRING ROUTED TO NO.63
TERMINAL FOR SEPARATE CONTROL.
1
1
2
2
3
WIRING FOR DC STARTERS ONLY
FWD/UP
0
REV/DWN
CONTROL POWER WIRING NOTES
CAUTION
READ AND FOLLOW INSTRUCTIONS PRIOR TO WIRING OR CONNECTING POWER! THIS PRODUCT CAN BE FACTORY
OR FIELD CONFIGURED FOR MULTIPLE CONTROL MODES OR CONTROL VOLTAGES. CHECK NAMEPLATE FOR
COIL VOLTAGE.
SEPARATE CONTROL POWER
FOR COIL VOLTAGES 120V AND LESS: CONNECT SEPARATE CONTROL LINES TO THE NO. 63 OR NO.61 TERMINAL
PER DIAGRAM ON THE TOP ADDER AUX. AND TO THE 96 TERMINAL ON THE OVERLOAD RELAY.
FOR COIL VOLTAGES GREATER THAN 120V: REMOVE WIRE "C2" IF SUPPLIED. IF WIRE "C1" IS TERMINATED ONL1,
DISCONNECT FROM L1. CONNECT SEPARATE CONTROL LINES TO THE "C1" WIRE OR APPROPRIATE PILOT DEVICE
TERMINAL PER DIAGRAM AND TO THE NO 96 TERMINAL ON THE OVERLOAD RELAY. .
COMMON CONTROL POWER
FOR COIL VOLTAGES 120V AND LESS: A ADD WIRE "C2" IF NOT SUPPLIED. ADD CONNECTOR BETWEEN L1 TERMINAL
AND THE NO. 61 OR NO.63 TERMINAL PER DIAGRAM ON THE TOP ADDER AUX. OR APPROPRIATE PILOT DEVICE
TERMINAL PER DIAGRAM.
FOR COIL VOLTAGES GREATER THAN 120V: ADD WIRE "C1" AND "C2" IF NOT SUPPLIED.
ote:N Source drawing reference wiring diagrams 286979 or 288257.
ote:N For kits with a green OFF light, an additional top added NC auxiliary is needed to be supplied by the customer.