Eaton CDAU-01/04 User Manual

Smart Dimming Actuator
CDAU-01/04, CDAU-01/04-I, CDAU-01/04-E
OFF
868.3 MHz
IP20
R, L, C, LED, ESL
M
1.5 mm
2
10 mm
Local input
A
B
Program
Mode
Actuator Type Load
CDAU-01/04 250 W
CDAU-01/04-I Local input 250 W
CDAU-01/04-E EMS, kWh 250 W
Neutral wire needed!
Nuldraad benodigd!
Nøytralleder nødvendig
Neutralleiter erforderlich!
Nulovy vodičzapotřebí!
+55°C*
-5°C
-25°C
+70°C
Technical Data / Technische gegevens / Tekniske data /
Technische Daten / Technická data
Power supply 230 VAC +10% -15%, 50 Hz
Load 0 - 250 W (0 - 250 VA)
LED, ESL: 0 - 100 W*
* Depending on the lamp type.
Power standby (Typical) 325 mW (EMS type: 425 mW)
EMS 0.5 W to 250 W,
5% ±0.5 W (>0.5 W)
Local Input 230 VAC (Max. 265 V)
Binary Input voltage Maximum 265 V (Same phase)
Input contact resistance < 10 kΩ reliably ON,
IN to L > 50 kΩ reliably OFF
Voltage difference < 1 V reliably ON
IN to L > 3 V reliably OFF
Overload protected (Auto recovery)
Short-circuit protected (Auto recovery)
Dimensions 49.5 x 45.5 x 18 mm (H x W x D)
55°C45°C
* Derating
-5°C
200
W
250
W
Danger
Lebensgefahr
Danger de mort
Nebezpečí
Nebezpečenstvo
Fare
Peligro
Életveszély
Pericolo di morte
Fare
Levensgevaar
Perigo
Niebezpieczenstwo
Varning
Vaara
Hayati Tehlike
Pericol
Installation by electricians only
Montage nur durch Elektrofachkräfte
Montage uniquement par un électricien
Montáž pouze osobami s elektrotechnickou kvalifikaci
Montáž iba osobami s elektrotechnickou kvalifikáciou
Må kun installeres af en aut. el-installatør
Debe ser instalado por un profesional eléctrico
Csak szakképzett személy szerelheti
Montaggio esclusivamente ad opera di personale specializzato
Må monteres av autorisert installatør Gr.L
Montage alleen door elektromonteurs
Deve ser instalado por um profissional
Montaz tylko przez uprawnionych instalatorów
Får endast utföras av behörig elektriker
Asennus vain sähköasentajan toimesta
Sadece uzman kisiler monte edebilir
Instalare numai de catre electricieni
1
MA-CDAU-01/04.qxp/02.2016a
IL019101ZU / 136211185
Eaton Industries (Austria) GmbH, Eugenia 1, 3943 Schrems, Austria
www.eaton.eu/documentation

Eaton CDAU-01/04 Specifications

General

Brand	Eaton
Model	CDAU-01/04
Category	Controller
Language	English

Summary

Installation, Safety, and Operation

Critical Safety Warnings

Provides essential safety information and hazard classifications for users.

Professional Installation Mandate

Specifies that only qualified electricians are permitted to install the device.

Neutral Wire Connection Requirement

Highlights the mandatory connection of a neutral wire for the actuator's functionality.

Technical Product Information

Technical Specifications and Data

Details electrical properties, load capacities, and device dimensions.

Actuator Model and Load Ratings

Lists available actuator types and their maximum load ratings.

Temperature Derating Information

Shows how ambient temperature affects the device's load handling capability.

Wiring Diagrams and Configuration

Actuator Wiring Examples

Illustrates connection diagrams for different actuator modes and local inputs.

Setting Local Input Modes

Explains how to assign functions to the local input based on button presses.

Configuring Dim Profiles

Details the procedure for setting dimming profiles for different load types.

Advanced Functions and Reset

Manual Switching and Testing

Describes how to manually operate and test the actuator's functions.

Sensor Assignment and Removal

Covers the process of adding or removing sensors from the basic operating mode.

Device Identification and Reset

Explains how to identify the device and reset it to factory default settings.

Declaration of Conformity

Product Compliance Statement

Official declaration that the product complies with relevant EU directives and standards.

Covered Directives and Standards

Lists the specific EU directives and harmonized standards the product adheres to.