Why is my Eaton Evolution 1550 overloaded?
If the Eaton UPS displays Button (10) and LEDs (13) and T (14) are ON and all the LEDs on the bargraph (8) flashing, it indicates that the percent load is exceeding the set overload level or the UPS capacity. To address this, verify the power consumption of the connected devices, disconnect any non-priority equipment, and review the overload level settings.
How to fix Eaton Evolution 1550 UPS battery fault?
If the Eaton UPS has LED (15) ON and all the LEDs on bargraph (11) are flashing, it indicates a battery fault detected during the automatic test. The suggested solution is to replace the battery module.
What to do if Eaton Evolution 1550 UPS button and LED are ON and LEDs on bargraph flash?
If the button and LEDs are ON and all the LEDs on the bargraph are flashing on your Eaton UPS, it means the percent load is greater than the set overload level or UPS capacity. To resolve this, check the power drawn by the connected devices and disconnect any non-priority devices. Also, check the overload level setting.
What to do if Eaton Evolution 1550 UPS button and LED are ON and all bargraph LEDs are flashing?
If the button and LED are ON and all the LEDs on the bargraph are flashing on your Eaton UPS, a critical overload has occurred on the UPS output. If AC input power fails, the load will not be supplied in battery mode. Check the power drawn by the connected devices and disconnect any non-priority devices.
Why is the LED ON and bargraph LEDs flashing on my Eaton Evolution 1550 UPS?
If the LED is ON and all the LEDs on the bargraph are flashing on your Eaton UPS, a battery fault has been detected during the automatic test. Replace the battery module.
How to fix Eaton Evolution 1550 when all LEDs go ON and then only one LED remains ON?
If, when starting your Eaton UPS, all the LEDs briefly turn ON, the buzzer beeps, and then only one LED remains ON, the remote power off (RPO) contact has been activated, preventing restart. To fix this, set the contact back to its normal position and press the button to restart.
What to do if Eaton UPS shows critical overload?
If the Eaton UPS experiences a critical overload, indicated by Button (10) and LED (15) being ON with all LEDs on bargraph (8) flashing, it means the UPS output is critically overloaded. In this situation, AC input power failure will result in the load not being supplied in battery mode. To resolve this, check the power consumption of connected devices and disconnect any non-priority devices to reduce the load.
Why does Eaton Evolution 1550 LED r (14) stay on?
When starting the Eaton UPS using button T (10), if all the LEDs illuminate briefly, the buzzer beeps once, and then LED r (14) remains lit, it signifies that the remote power off (RPO) contact has been activated, shutting down the UPS and preventing restart. To resolve this, revert the contact to its normal position and then press button (24) to initiate a restart.
Discusses EATON's environmental protection policy and eco-design approach for products.
States the product does not contain CFCs, HCFCs, or asbestos.
Details recycling of cardboard and polyethylene packing materials.
Explains EATON's process for product and battery disposal and recycling.
Lists compliance standards like FCC, UL, and IEC for the UPS.
Details risks associated with internal voltage, batteries, and proper grounding.
Covers installation order, circuit breakers, environment, and storage.
Advises on two-person handling, battery charging during storage, and battery module replacement.
Notes eco-design, recycling, and lead-acid battery warnings.
Explains the meaning of the triangular warning symbol for critical instructions.
Explains the meaning of the 'i' symbol for information, advice, or help.
Explains the meaning of the symbol indicating a visual indication.
Explains the meaning of the symbol indicating an action to be performed.
Explains the meaning of the symbol indicating an audible signal.
Explains the meaning of the symbol representing an LED being off.
Explains the meaning of the symbol representing an LED being on.
Explains the meaning of the symbol representing an LED flashing.
Displays physical dimensions and weights for Tower and Rack models.
Details the rear panel connectors and ports for Tower and Rack models.
Describes the front panel controls, buttons, and LEDs.
Guides on how to unpack the UPS and verify all included components.
Provides instructions for installing the UPS in a tower configuration.
Guides on mounting the UPS into a rack system using rails.
Details the rack mounting and wall mounting procedures for the 650 Rack model.
Explains how to connect RS232/USB ports and install communication cards.
Details how to connect the UPS input power cord and output loads to equipment.
Describes the process of starting the UPS and its normal operational status.
Explains battery power usage, low-battery warnings, and end of backup time.
Details how the UPS behavior when AC power is restored after an outage.
Explains how to properly shut down the UPS using the front panel button.
Describes RPO and ROO remote control functions via a rear panel connector.
Allows adjustment of output voltage and overload alarm thresholds.
Covers settings for transfer to battery based on voltage levels.
Allows adjustment of the UPS sensitivity level to power conditions.
Includes settings for automatic start, cold start, energy-saving mode, and battery level.
Covers battery test intervals, low-battery warnings, and audio alarms.
Provides a table of common UPS indications, their diagnostics, and corrective actions.
Step-by-step instructions for removing and replacing the battery module in a tower UPS.
Outlines safety precautions and steps for replacing the battery in a rack-mount UPS.
Instructions for installing the new battery module, referencing reverse order of removal.
Provides detailed technical specifications for the Evolution UPS range.
Guides users on configuring programmable outlets using the Personal Solution-Pac software.
Details setting the shutdown timer for programmable outlets via software.
Defines key terms and concepts used throughout the manual.
General| Type | Line Interactive |
|---|---|
| Nominal Input Voltage | 230 V |
| Form Factor | Tower |
| Humidity | 0-95% non-condensing |
| Warranty | 2 years |
| Model | Evolution 1550 |
| Power Rating | 1550 VA |
| Output Voltage | 230 V |
| Battery Type | Sealed Lead-Acid (SLA) |
| Typical Recharge Time | 4-6 hours to 90% |
| Operating Temperature | 0 to 40°C |
| Communication Ports | USB |
| Technology | Line Interactive |
| Topology | Line Interactive |
To Next Page