EasyManua.ls Logo

Eaton Vickers V-104-A-10 - User Manual

Eaton Vickers V-104-A-10
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
I-3100-SReprinted 12/1/86
Single Stage Single and
Double Vane Pumps
V104, 124, 134,144 V109, 129, 139, 149
V105, 125, 135, 145 V35*, 36*, 45*, 46*
V108, 128, 138, 148 (V)VF-**-**, (V)VG-**-**
Vickers
®
Vane Pumps
Overhaul Manual

Table of Contents

Questions and Answers

  • R
    Rodney SchwartzAug 17, 2025
    What to do if my Eaton Vickers V-104-A-10 is not delivering fluid?
    • M
      Michael WongAug 17, 2025
      If your Eaton Water Pump isn't delivering fluid, several issues could be the cause. First, the pump might be driven in the wrong direction; immediately reverse it to prevent seizure and check the drive rotation against the arrow on the pump body. Other potential causes include a broken drive shaft or sheared shaft key, a blocked fluid intake pipe, air leaks at the intake, a low oil level, or vanes stuck in rotor slots. Check each of these possibilities, and take corrective actions such as replacing damaged parts or adding new fluid of the proper viscosity.
  • E
    Elijah Hall PhDAug 20, 2025
    Why is my Eaton Vickers V-104-A-10 making noise?
    • J
      Juan HebertAug 20, 2025
      If your Eaton Water Pump is making noise, it could be due to several reasons. A partially clogged intake strainer or restricted intake pipe, a defective bearing, an air leak at the pump intake piping joints or pump shaft seal, or coupling misalignment could be the cause. To troubleshoot, drain the system and clean the intake pipe, and clean or replace the strainer. Also, test for air leaks by pouring oil on joints and around the drive shaft and listen for a change in operation. If there is a defective bearing, disassemble the pump and replace it. Re-align shafts to fix coupling misalignment.
  • B
    Brandon WelchAug 22, 2025
    How to fix air leaks at intake of Eaton Water Pump?
    • J
      Joshua BuchananAug 22, 2025
      To fix air leaks at the intake of your Eaton Water Pump, check the intake connection for air leaks and tighten it securely.
  • S
    Shelby GonzalesAug 26, 2025
    What to do if the oil level is too low in Eaton Vickers V-104-A-10?
    • N
      Nicole HoweAug 26, 2025
      If the oil level is too low in your Eaton Water Pump, ensure that the fluid level is above the intake opening in the intake pipe.
  • P
    Pamela AndersonAug 28, 2025
    How to fix Eaton Vickers V-104-A-10 driven in wrong direction?
    • D
      David BauerAug 28, 2025
      If the Eaton Water Pump is driven in the wrong direction of rotation, it must be reversed immediately to prevent seizure. Check the direction of drive rotation against the proper pump rotation as indicated by the arrow on the body.
  • J
    Jamie Sims MDAug 30, 2025
    What to do if fluid intake pipe is blocked in Eaton Vickers V-104-A-10 Water Pump?
    • K
      Kathryn WintersAug 31, 2025
      If the fluid intake pipe in your Eaton Water Pump is blocked or the oil viscosity is too heavy to pick up prime, drain the complete system. Add new fluid of proper viscosity and filter the new fluid as recommended.
  • R
    reevespennySep 2, 2025
    How to test Eaton Water Pump for air leak at pump intake piping?
    • K
      Kyle RodriguezSep 3, 2025
      To test your Eaton Water Pump for an air leak at the pump intake piping joints or pump shaft seal, pour oil on joints and around the drive shaft. Listen for a change in operation and then tighten the joints affected.
  • A
    Andrea TaylorSep 5, 2025
    How to fix coupling misalignment in Eaton Vickers V-104-A-10 Water Pump?
    • B
      barbara35Sep 5, 2025
      To fix coupling misalignment in your Eaton Water Pump, re-align the shafts.
  • P
    Preston MasonSep 8, 2025
    What if vane is stuck in rotor slots of Eaton Water Pump?
    • S
      Samuel JuarezSep 8, 2025
      If a vane or vanes are stuck in the rotor slots of your Eaton Water Pump, inspect the rotor slots for wedged chips or foreign particles and replace all damaged parts. Flush the complete system thoroughly by recommended processes and fill the system with new, clean hydraulic fluid.
  • D
    Dennis WilliamsSep 12, 2025
    How to fix defective bearing in Eaton Vickers V-104-A-10 Water Pump?
    • K
      Kenneth JohnsonSep 12, 2025
      To fix a defective bearing in your Eaton Water Pump, disassemble the pump and replace the bearing.

Summary

Section I - Operating Characteristics

Section II - Description

Section III - Principles of Operation

Pump Operation

Explains how the pump operates, including fluid flow and chamber dynamics.

Pump Lubrication

Details lubrication requirements for older pump designs and recommendations.

Routine Inspection and Maintenance

Outlines procedures for regular checks and upkeep of the pump to ensure optimal performance.

Section IV - Overhaul

General Overhaul Information

Provides general guidance and kit information for pump overhaul procedures.

Disassembly Procedures

Details the step-by-step process for safely taking the pump apart for maintenance.

Reassembly Procedures

Guides on how to correctly put the pump back together after overhaul.

Product Life Factors

Discusses factors influencing the longevity and performance of the pumps.

Section V - Cartridge Assembly and Installation

Cartridge Assembly Details

Explains the process and precautions for assembling pump cartridges correctly.

Pump Installation Guidance

Provides instructions for installing pump cartridges, considering rotation direction.

Head Screw Adjustment

Details the procedure for adjusting head screws during pump assembly.

Section VI - Troubleshooting

Section VII - Parts & Illustration Drawings

Eaton Vickers V-104-A-10 Specifications

General IconGeneral
BrandEaton
ModelVickers V-104-A-10
CategoryWater Pump
LanguageEnglish

Related product manuals