Eaton Vickers V-135-X-20 User Manual (English)

Questions and Answers:

A
Alexis JonesAug 17, 2025
What to do if my Eaton Water Pump is not delivering fluid?
- R
  robinsonshannonAug 17, 2025
  If your Eaton Water Pump isn't delivering fluid, several issues could be the cause. First, the pump might be driven in the wrong direction; immediately reverse it to prevent seizure and check the drive rotation against the arrow on the pump body. Other potential causes include a broken drive shaft or sheared shaft key, a blocked fluid intake pipe, air leaks at the intake, a low oil level, or vanes stuck in rotor slots. Check each of these possibilities, and take corrective actions such as replacing damaged parts or adding new fluid of the proper viscosity.
D
Denise SinghAug 20, 2025
Why is my Eaton Water Pump making noise?
- D
  Dustin CabreraAug 20, 2025
  If your Eaton Water Pump is making noise, it could be due to several reasons. A partially clogged intake strainer or restricted intake pipe, a defective bearing, an air leak at the pump intake piping joints or pump shaft seal, or coupling misalignment could be the cause. To troubleshoot, drain the system and clean the intake pipe, and clean or replace the strainer. Also, test for air leaks by pouring oil on joints and around the drive shaft and listen for a change in operation. If there is a defective bearing, disassemble the pump and replace it. Re-align shafts to fix coupling misalignment.
A
Anna SimmonsAug 22, 2025
How to fix air leaks at intake of Eaton Vickers V-135-X-20 Water Pump?
- E
  Elizabeth GrayAug 22, 2025
  To fix air leaks at the intake of your Eaton Water Pump, check the intake connection for air leaks and tighten it securely.
J
Joseph McdowellAug 26, 2025
What to do if the oil level is too low in Eaton Vickers V-135-X-20 Water Pump?
- U
  uandersonAug 26, 2025
  If the oil level is too low in your Eaton Water Pump, ensure that the fluid level is above the intake opening in the intake pipe.
C
cruztammyAug 28, 2025
How to fix Eaton Vickers V-135-X-20 driven in wrong direction?
- J
  Justin RobertsAug 28, 2025
  If the Eaton Water Pump is driven in the wrong direction of rotation, it must be reversed immediately to prevent seizure. Check the direction of drive rotation against the proper pump rotation as indicated by the arrow on the body.
R
Rebecca LeeAug 31, 2025
What to do if fluid intake pipe is blocked in Eaton Vickers V-135-X-20 Water Pump?
- M
  Matthew RodgersAug 31, 2025
  If the fluid intake pipe in your Eaton Water Pump is blocked or the oil viscosity is too heavy to pick up prime, drain the complete system. Add new fluid of proper viscosity and filter the new fluid as recommended.
M
Michael MckeeSep 2, 2025
How to test Eaton Water Pump for air leak at pump intake piping?
- R
  Rebecca BryantSep 2, 2025
  To test your Eaton Water Pump for an air leak at the pump intake piping joints or pump shaft seal, pour oil on joints and around the drive shaft. Listen for a change in operation and then tighten the joints affected.
R
Ronald HarrisSep 5, 2025
How to fix coupling misalignment in Eaton Vickers V-135-X-20?
- D
  David Smith IISep 5, 2025
  To fix coupling misalignment in your Eaton Water Pump, re-align the shafts.
C
Charles MooreSep 8, 2025
What if vane is stuck in rotor slots of Eaton Vickers V-135-X-20 Water Pump?
- B
  Brittany GriffinSep 8, 2025
  If a vane or vanes are stuck in the rotor slots of your Eaton Water Pump, inspect the rotor slots for wedged chips or foreign particles and replace all damaged parts. Flush the complete system thoroughly by recommended processes and fill the system with new, clean hydraulic fluid.