Eaton Vickers V-109-EC-10

Questions and Answers

V
Vincent RobertsAug 17, 2025
What to do if my Eaton Vickers V-109-EC-10 is not delivering fluid?
- B
  bmcdonaldAug 17, 2025
  If your Eaton Water Pump isn't delivering fluid, several issues could be the cause. First, the pump might be driven in the wrong direction; immediately reverse it to prevent seizure and check the drive rotation against the arrow on the pump body. Other potential causes include a broken drive shaft or sheared shaft key, a blocked fluid intake pipe, air leaks at the intake, a low oil level, or vanes stuck in rotor slots. Check each of these possibilities, and take corrective actions such as replacing damaged parts or adding new fluid of the proper viscosity.
E
Elizabeth GordonAug 20, 2025
Why is my Eaton Vickers V-109-EC-10 making noise?
- T
  Teresa KellyAug 20, 2025
  If your Eaton Water Pump is making noise, it could be due to several reasons. A partially clogged intake strainer or restricted intake pipe, a defective bearing, an air leak at the pump intake piping joints or pump shaft seal, or coupling misalignment could be the cause. To troubleshoot, drain the system and clean the intake pipe, and clean or replace the strainer. Also, test for air leaks by pouring oil on joints and around the drive shaft and listen for a change in operation. If there is a defective bearing, disassemble the pump and replace it. Re-align shafts to fix coupling misalignment.
H
Harry ForbesAug 22, 2025
How to fix air leaks at intake of Eaton Vickers V-109-EC-10 Water Pump?
- S
  sarataylorAug 22, 2025
  To fix air leaks at the intake of your Eaton Water Pump, check the intake connection for air leaks and tighten it securely.
S
Scott DiazAug 26, 2025
What to do if the oil level is too low in Eaton Water Pump?
- M
  Mitchell RhodesAug 26, 2025
  If the oil level is too low in your Eaton Water Pump, ensure that the fluid level is above the intake opening in the intake pipe.
G
George LittleAug 28, 2025
How to fix Eaton Water Pump driven in wrong direction?
- T
  Travis WoodardAug 28, 2025
  If the Eaton Water Pump is driven in the wrong direction of rotation, it must be reversed immediately to prevent seizure. Check the direction of drive rotation against the proper pump rotation as indicated by the arrow on the body.
N
Nathan HendersonAug 31, 2025
What to do if fluid intake pipe is blocked in Eaton Water Pump?
- J
  Jamie GrayAug 31, 2025
  If the fluid intake pipe in your Eaton Water Pump is blocked or the oil viscosity is too heavy to pick up prime, drain the complete system. Add new fluid of proper viscosity and filter the new fluid as recommended.
K
Karen SmithSep 2, 2025
How to test Eaton Vickers V-109-EC-10 for air leak at pump intake piping?
- S
  Stephen LoveSep 3, 2025
  To test your Eaton Water Pump for an air leak at the pump intake piping joints or pump shaft seal, pour oil on joints and around the drive shaft. Listen for a change in operation and then tighten the joints affected.
A
Anthony YoungSep 5, 2025
How to fix coupling misalignment in Eaton Water Pump?
- C
  Cindy YangSep 5, 2025
  To fix coupling misalignment in your Eaton Water Pump, re-align the shafts.
K
Kelly HowardSep 8, 2025
What if vane is stuck in rotor slots of Eaton Vickers V-109-EC-10?
- D
  Doris SheltonSep 8, 2025
  If a vane or vanes are stuck in the rotor slots of your Eaton Water Pump, inspect the rotor slots for wedged chips or foreign particles and replace all damaged parts. Flush the complete system thoroughly by recommended processes and fill the system with new, clean hydraulic fluid.
S
samuelnguyenSep 12, 2025
How to fix defective bearing in Eaton Water Pump?
- J
  Jasmine EstesSep 12, 2025
  To fix a defective bearing in your Eaton Water Pump, disassemble the pump and replace the bearing.