EasyManua.ls Logo

Eaton Vickers V-104-D-10 - User Manual

Eaton Vickers V-104-D-10
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
I-3100-SReprinted 12/1/86
Single Stage Single and
Double Vane Pumps
V104, 124, 134,144 V109, 129, 139, 149
V105, 125, 135, 145 V35*, 36*, 45*, 46*
V108, 128, 138, 148 (V)VF-**-**, (V)VG-**-**
Vickers
®
Vane Pumps
Overhaul Manual

Table of Contents

Questions and Answers

  • T
    Tracey McguireAug 17, 2025
    What to do if my Eaton Vickers V-104-D-10 Water Pump is not delivering fluid?
    • K
      Katrina RayAug 17, 2025
      If your Eaton Water Pump isn't delivering fluid, several issues could be the cause. First, the pump might be driven in the wrong direction; immediately reverse it to prevent seizure and check the drive rotation against the arrow on the pump body. Other potential causes include a broken drive shaft or sheared shaft key, a blocked fluid intake pipe, air leaks at the intake, a low oil level, or vanes stuck in rotor slots. Check each of these possibilities, and take corrective actions such as replacing damaged parts or adding new fluid of the proper viscosity.
  • J
    Jeffery SanchezAug 20, 2025
    Why is my Eaton Vickers V-104-D-10 Water Pump making noise?
    • K
      kingdianaAug 20, 2025
      If your Eaton Water Pump is making noise, it could be due to several reasons. A partially clogged intake strainer or restricted intake pipe, a defective bearing, an air leak at the pump intake piping joints or pump shaft seal, or coupling misalignment could be the cause. To troubleshoot, drain the system and clean the intake pipe, and clean or replace the strainer. Also, test for air leaks by pouring oil on joints and around the drive shaft and listen for a change in operation. If there is a defective bearing, disassemble the pump and replace it. Re-align shafts to fix coupling misalignment.
  • M
    Matthew GarciaAug 22, 2025
    How to fix air leaks at intake of Eaton Water Pump?
    • O
      oconnelllindsayAug 22, 2025
      To fix air leaks at the intake of your Eaton Water Pump, check the intake connection for air leaks and tighten it securely.
  • D
    Daryl GrayAug 26, 2025
    What to do if the oil level is too low in Eaton Vickers V-104-D-10 Water Pump?
    • W
      williamsdanielAug 26, 2025
      If the oil level is too low in your Eaton Water Pump, ensure that the fluid level is above the intake opening in the intake pipe.
  • A
    Andrea HuffmanAug 28, 2025
    How to fix Eaton Vickers V-104-D-10 driven in wrong direction?
    • E
      erinroblesAug 28, 2025
      If the Eaton Water Pump is driven in the wrong direction of rotation, it must be reversed immediately to prevent seizure. Check the direction of drive rotation against the proper pump rotation as indicated by the arrow on the body.
  • S
    Sarah MorganAug 30, 2025
    What to do if fluid intake pipe is blocked in Eaton Water Pump?
    • C
      chendricksAug 31, 2025
      If the fluid intake pipe in your Eaton Water Pump is blocked or the oil viscosity is too heavy to pick up prime, drain the complete system. Add new fluid of proper viscosity and filter the new fluid as recommended.
  • E
    Erin MeyerSep 3, 2025
    How to test Eaton Vickers V-104-D-10 for air leak at pump intake piping?
    • B
      Brendan ArcherSep 3, 2025
      To test your Eaton Water Pump for an air leak at the pump intake piping joints or pump shaft seal, pour oil on joints and around the drive shaft. Listen for a change in operation and then tighten the joints affected.
  • M
    michelle34Sep 5, 2025
    How to fix coupling misalignment in Eaton Vickers V-104-D-10 Water Pump?
    • J
      John HenrySep 5, 2025
      To fix coupling misalignment in your Eaton Water Pump, re-align the shafts.
  • K
    Kathryn MillsSep 8, 2025
    What if vane is stuck in rotor slots of Eaton Vickers V-104-D-10?
    • C
      christina15Sep 8, 2025
      If a vane or vanes are stuck in the rotor slots of your Eaton Water Pump, inspect the rotor slots for wedged chips or foreign particles and replace all damaged parts. Flush the complete system thoroughly by recommended processes and fill the system with new, clean hydraulic fluid.
  • T
    Todd MarksSep 12, 2025
    How to fix defective bearing in Eaton Water Pump?
    • A
      angela16Sep 12, 2025
      To fix a defective bearing in your Eaton Water Pump, disassemble the pump and replace the bearing.

Summary

Vane Pump Series Overview

Operating Characteristics

Single Pump Series Performance

Presents performance data, including delivery and horsepower, for single stage single pump models.

Double Pump Series - Small Series Combination

Details performance data for double pump series with small series head end pump.

Double Pump Series - Intermediate and Small Series

Details performance data for double pump series, intermediate and small series combinations.

Double Pump Series - Large and Small Series

Details performance data for double pump series, large and small series combinations.

Double Pump Series - Large and Intermediate Series

Details performance data for double pump series, large and intermediate series combinations.

Overhaul

Routine Inspection and Maintenance

Disassembly and Part Inspection

Reassembly Procedure

Cartridge Assembly and Installation

Cartridge Assembly Steps

Pump Installation Guidelines

Troubleshooting

Troubleshooting Fluid Delivery Issues

Diagnosing and resolving problems related to the pump not delivering fluid.

Troubleshooting Pump Noise

Eaton Vickers V-104-D-10 Specifications

General IconGeneral
BrandEaton
ModelVickers V-104-D-10
CategoryWater Pump
LanguageEnglish

Related product manuals