EasyManua.ls Logo

Eaton Vickers V-105-Y-10 - User Manual

Eaton Vickers V-105-Y-10
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
I-3100-SReprinted 12/1/86
Single Stage Single and
Double Vane Pumps
V104, 124, 134,144 V109, 129, 139, 149
V105, 125, 135, 145 V35*, 36*, 45*, 46*
V108, 128, 138, 148 (V)VF-**-**, (V)VG-**-**
Vickers
®
Vane Pumps
Overhaul Manual

Table of Contents

Questions and Answers

  • M
    Mrs. Toni ThomasAug 17, 2025
    What to do if my Eaton Vickers V-105-Y-10 Water Pump is not delivering fluid?
    • C
      Courtney DelacruzAug 17, 2025
      If your Eaton Water Pump isn't delivering fluid, several issues could be the cause. First, the pump might be driven in the wrong direction; immediately reverse it to prevent seizure and check the drive rotation against the arrow on the pump body. Other potential causes include a broken drive shaft or sheared shaft key, a blocked fluid intake pipe, air leaks at the intake, a low oil level, or vanes stuck in rotor slots. Check each of these possibilities, and take corrective actions such as replacing damaged parts or adding new fluid of the proper viscosity.
  • K
    Kim HamptonAug 19, 2025
    Why is my Eaton Water Pump making noise?
    • L
      Laura OrtizAug 19, 2025
      If your Eaton Water Pump is making noise, it could be due to several reasons. A partially clogged intake strainer or restricted intake pipe, a defective bearing, an air leak at the pump intake piping joints or pump shaft seal, or coupling misalignment could be the cause. To troubleshoot, drain the system and clean the intake pipe, and clean or replace the strainer. Also, test for air leaks by pouring oil on joints and around the drive shaft and listen for a change in operation. If there is a defective bearing, disassemble the pump and replace it. Re-align shafts to fix coupling misalignment.
  • G
    gfisherAug 22, 2025
    How to fix air leaks at intake of Eaton Water Pump?
    • A
      Amanda HebertAug 22, 2025
      To fix air leaks at the intake of your Eaton Water Pump, check the intake connection for air leaks and tighten it securely.
  • J
    Jerry HamiltonAug 25, 2025
    What to do if the oil level is too low in Eaton Vickers V-105-Y-10 Water Pump?
    • D
      Denise MccannAug 26, 2025
      If the oil level is too low in your Eaton Water Pump, ensure that the fluid level is above the intake opening in the intake pipe.
  • Y
    yhallAug 27, 2025
    How to fix Eaton Vickers V-105-Y-10 Water Pump driven in wrong direction?
    • L
      Logan ThompsonAug 28, 2025
      If the Eaton Water Pump is driven in the wrong direction of rotation, it must be reversed immediately to prevent seizure. Check the direction of drive rotation against the proper pump rotation as indicated by the arrow on the body.
  • T
    Todd ColonAug 30, 2025
    What to do if fluid intake pipe is blocked in Eaton Vickers V-105-Y-10?
    • M
      Molly MillerAug 30, 2025
      If the fluid intake pipe in your Eaton Water Pump is blocked or the oil viscosity is too heavy to pick up prime, drain the complete system. Add new fluid of proper viscosity and filter the new fluid as recommended.
  • H
    Holly BentonSep 2, 2025
    How to test Eaton Vickers V-105-Y-10 for air leak at pump intake piping?
    • S
      Sharon HansenSep 2, 2025
      To test your Eaton Water Pump for an air leak at the pump intake piping joints or pump shaft seal, pour oil on joints and around the drive shaft. Listen for a change in operation and then tighten the joints affected.
  • S
    Shawn BrownSep 5, 2025
    How to fix coupling misalignment in Eaton Vickers V-105-Y-10 Water Pump?
    • D
      Diana StephensSep 5, 2025
      To fix coupling misalignment in your Eaton Water Pump, re-align the shafts.
  • M
    Michelle JacksonSep 7, 2025
    What if vane is stuck in rotor slots of Eaton Vickers V-105-Y-10?
    • A
      Antonio WagnerSep 7, 2025
      If a vane or vanes are stuck in the rotor slots of your Eaton Water Pump, inspect the rotor slots for wedged chips or foreign particles and replace all damaged parts. Flush the complete system thoroughly by recommended processes and fill the system with new, clean hydraulic fluid.
  • S
    Suzanne PittsSep 10, 2025
    How to fix defective bearing in Eaton Vickers V-105-Y-10?
    • A
      Amber ChapmanSep 12, 2025
      To fix a defective bearing in your Eaton Water Pump, disassemble the pump and replace the bearing.

Summary

Operating Characteristics

General Operating Parameters

Summarizes general operating parameters like type, series, pressure, speed, fluid, and mounting.

Single Pump Series Performance Data

Details performance characteristics (delivery, horsepower) for single-stage single pumps.

Double Pump Series Performance Data (Small Series)

Details performance for double pumps, small series combination.

Description and Principles of Operation

General Pump Description

Explains the manual covers service and maintenance for single and double vane pumps.

Pump Mechanism and Fluid Flow

Explains the pumping action by cartridges, rotor, vanes, and cam ring.

Lubrication Requirements

Details lubrication needs for older pump designs and grease fitting recommendations.

Routine Inspection and Maintenance

Outlines checks for connections, fluid level, filters, and air breathers.

Overhaul Procedures

General Overhaul Information

Notes that overhaul can be done with cartridge and gasket kits.

Disassembly and Reassembly

Details steps for taking the pump apart and reassembling it, including safety warnings.

Product Life Factors

Discusses factors influencing product longevity like duty cycle and system cleanliness.

Cartridge Assembly and Installation

Cartridge Assembly Details

Explains how to assemble pump cartridges, noting the stepped diameter locating pin.

Pump Installation and Rotation

Guides on installing the cartridge for right or left-hand rotation and checking shaft movement.

Head Screw Adjustment

Describes how to adjust head screws for proper seating and shaft rotation.

Troubleshooting and System Operation

Troubleshooting Common Pump Issues

Covers common pump problems like no delivery or noise, with probable causes and remedies.

System Operation Recommendations

Provides advice on pump priming, installation, drive types, and pressure/speed limitations.

Parts and Illustration Drawings

Intermediate Series Cartridge Illustrations

Shows and describes modified cartridge parts for the intermediate series.

Pump Series Parts Reference

Lists part numbers for service and installation drawings of single pump series.

Double Pump Parts Illustrations

Presents typical illustration and part breakdown for double pump assemblies.

Eaton Vickers V-105-Y-10 Specifications

General IconGeneral
BrandEaton
ModelVickers V-105-Y-10
CategoryWater Pump
LanguageEnglish

Related product manuals