EBARA GS Series - User Manual

Questions and Answers

A
Alexandra JamesAug 19, 2025
How to troubleshoot EBARA Water Pump when the motor will not start?
- T
  Teresa MillerAug 19, 2025
  If the EBARA Water Pump motor won't start, several factors could be at play. First, the control panel might not be working correctly, so check all conditions. There may be faults in the power supply, so check and repair. It could also be a motor failure, requiring a motor repair. Other potential causes include friction on the rotation shaft, which you can try to rotate by hand and then reassemble, or a clogged pump, in which case you should remove any foreign bodies.
E
Erika RogersAug 21, 2025
What to do if my EBARA Water Pump has a power surge?
- F
  flowerssamuelAug 21, 2025
  If your EBARA Water Pump experiences a power surge, the voltage might be low, or there could be an imbalance between the phases, so check the power supply. The flow rate might be too high, or the head might be too low, so partially shut off the delivery valve. There may be foreign bodies inside the pump, so remove them. Also, the mechanical seal may not have been fitted correctly, so fit it correctly. The bearings may be damaged, so replace them. In case of friction in the rotation areas or if the shaft is bent, repair in specialist workshop. Ensure the rotation direction is correct by checking and correcting the connection. High liquid density and/or viscosity can also cause power surges.
R
Roberto HarrisAug 25, 2025
Why is my EBARA Water Pump making excessive operating vibration and noise?
- E
  Erik StewartAug 25, 2025
  Excessive vibration and noise in your EBARA Water Pump can stem from several issues. Check the installation for any faults. Damaged bearings can also cause this, so consider replacing them. If the flow rate is too high, reduce the delivery valve's aperture; if it's too low, increase it. A blocked impeller can also be the culprit, so remove any foreign bodies. Ensure the rotation direction is correct by checking and correcting the connection. For friction in rotation areas or a bent shaft, professional repair is needed. Cavitation may also be the reason. Finally, vibrations in the piping can contribute, so reinforce the piping or fit an inverter.
S
Scott WelchAug 26, 2025
Why does my EBARA Water Pump have a low flow rate?
- C
  Casey HardinAug 26, 2025
  A low flow rate in your EBARA Water Pump can be caused by several factors. The direction of rotation might not be correct, so correct the electrical connections. The rotation speed might be low, so measure the RPM with a tachometer. Low voltage can also be a cause, so check the power supply. Blockages in the bottom valve, filter, or impeller can restrict flow, so remove any foreign bodies. A clogged pipe can also reduce flow, so remove any foreign bodies. Air entering the system can also cause low flow, so check and repair the suction pipe and shaft seal.
D
Douglas LeachAug 27, 2025
What causes my EBARA Water Pump motor to not start?
- L
  larrykirkAug 28, 2025
  If the EBARA Water Pump motor doesn't start, it could be due to a broken or cut winding, requiring repair in a specialist workshop. A short-circuited stator or grounding can also prevent starting, both necessitating professional repair. Blocked bearings can hinder the motor, requiring bearing repair. Low voltage can be a factor, so change the nominal voltage. Finally, loss of phases in the power supply can stop the motor, so check the power supply.
S
steven12Aug 30, 2025
Why is my EBARA Water Pump motor overheating and emitting smoke or a bad smell?
- M
  Meghan MathewsAug 30, 2025
  If your EBARA Water Pump motor is overheating and there's smoke or a bad smell, it could be due to high power surges, so correct the power surges. A blocked fan can also cause overheating, so release the fan. Using the wrong voltage can lead to this issue, so change the motor for one with the appropriate voltage. Blocked bearings can also cause overheating, so repair the bearings. A short-circuited or grounded stator will cause overheating too, and will need repair in specialist workshop.
T
Thomas WrightSep 1, 2025
What causes abnormal noise or excessive vibrations in my EBARA Water Pump?
- B
  Brittany JacksonSep 1, 2025
  Abnormal noise or excessive vibrations in your EBARA Water Pump can arise from several issues. Operation without a phase can cause this, so check the power supply. Power surges can also lead to these problems, so correct the power surges. Friction between the rotor and stator can be a cause, so align and/or replace the bearing. Obstructions in the cooling fan can contribute, so remove any foreign bodies. A fault in installing the motor can cause these issues, so connect the pump correctly. Poor Star/Delta commutation can also be a factor, so correct the cabling.
A
abrownSep 3, 2025
Why is there excessive water leakage from the shaft seal of my EBARA Water Pump?
- P
  Philip PenaSep 3, 2025
  Excessive water leakage from the shaft seal of your EBARA Water Pump could be due to a defective fitting of the mechanical seal, so fit it correctly. The mechanical seal itself might be damaged, so replace the mechanical seal. Overpressure in delivery can also cause leakage, so review the project. Finally, a bent shaft can lead to this issue, so repair in specialist workshop.
R
Robert LopezSep 5, 2025
What could cause continued low flow rate in my EBARA Water Pump?
- K
  Kenneth BergerSep 5, 2025
  Continued low flow rate in your EBARA Water Pump can be attributed to several factors. Leakage in the delivery pipe can reduce flow, so check and repair. A worn impeller can also cause this, so check the impeller. Significant head losses in the system can impact flow, so review the project. High liquid temperature or volatile liquid can be a cause, so review the project. Finally, cavitation can lead to low flow, so seek expert advice.
C
Chelsea AlexanderSep 8, 2025
What to do if EBARA Water Pump has no flow rate?
- S
  sean83Sep 8, 2025
  If your EBARA Water Pump has no flow rate, it could be because the pump does not turn, so check that the impeller is free. The delivery valve might be closed or half-closed, so open the valve. Additionally, the suction head might be too low for the pump, so check the project.