EasyManua.ls Logo

EBARA 4WN Series - User Manual

EBARA 4WN Series
51 pages
Go to English
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
4WN
by EBARA PUMPS EUROPE
ORIGINAL BEDIENUNGSANLEITUNG
ORIGINAL INSTRUCTION MANUAL
MODE D'EMPLOI D'ORIGINE
ORIGINELE GEBRUIKSAANWIJZING
ORIGINAL INSTRUKTIONSBOK
ORIGINAL BETJENINGSVEJLEDNING
ECO FRIENDLY MATERIALSECO FRIENDLY MATERIALS
GREEN TECHNOLOGYGREEN TECHNOLOGY
ECO FRIENDLY MATERIALSECO FRIENDLY MATERIALS
GREEN TECHNOLOGYGREEN TECHNOLOGY
MATERIALS MATE RI AL S
ECOFRIENDLYECOFRIENDLY
ISO 9001 CERTIFIEDISO 9001 CERTIFIED
Q UALITYQUALITY
EuP READYEuP READY
EFFICIENCYEFFICIENCY
REPLACEMENT WARRANTYREPLACEMENT WARRANTY
RELIABILITYRELIABILITY

Table of Contents

Questions and Answers

  • V
    vicki21Aug 4, 2025
    Why is my EBARA 4WN Water Pump running but not pumping any water?
    • C
      Cameron MartinAug 5, 2025
      Several issues could be the cause: * The water level in the borehole might be too low. Try reducing the pumping volume, lowering the pump further, or using a pump with a smaller output. * The non-return valve could be closed or blocked. In that case, pull the pump out of the borehole and clean or replace the non-return valve. * The non-return valve on the pressure side is closed. You should open the non-return valve. * The intake screen might be blocked. Pull the pump out of the borehole and clean or replace the intake screen. * Motor malfunction. * The pump is faulty. In this case, repair or replace the pump.
  • G
    guerrerojasonAug 19, 2025
    How to troubleshoot reduced performance in my EBARA Water Pump?
    • M
      Michael HughesAug 19, 2025
      If your pump is running but with reduced performance, consider the following: * The pressure pipe might be partially blocked by dirt, leaking, or damaged. Clean the pressure pipe, mend the leak, or replace it. * The pump may be immersed too deep into the borehole and is covered by sand or solids. Reduce the immersion depth. * The non-return valve might be only partially open. Pull the pump out of the borehole and clean or replace the non-return valve. * The intake screen might be dirty. Pull the pump out of the borehole and clean or replace the intake screen. * Pump getting too hot. Fit the pump with a cooling jacket. * Motor malfunction. Measure motor current.
  • E
    Edward GrahamAug 27, 2025
    What to do if my EBARA Water Pump won’t start?
    • D
      Dustin JohnsonAug 27, 2025
      If your EBARA water pump won’t start, here are a few things to check: * The motor protection switch may have been triggered. Remove the plug from the socket for at least one minute. * There might be no power supply. Have the electrical installation checked by a qualified electrician. * There could be a faulty pump or underwater cable. Repair or replace the pump or underwater cable.
  • J
    jonathansavageNov 10, 2025
    What to do if my EBARA 4WN Water Pump switching on and off frequently?
    • M
      mary44Nov 10, 2025
      If your pump is switching on and off frequently, especially with an installed pressure compensation tank or pressure switch, consider these potential causes: * The inlet pressure in the compensation tank might be too low. The inlet pressure of the compensation tank should be about 10% lower than the pump’s switch-on pressure. * The compensation tank could be too small. Increase the volume of the compensation tank by installing a further tank or replace it. * The compensation tank membrane might be damaged. Replace the compensation tank. * The difference between switch-on and switch-off pressure set on the pressure switch is too low. Increase the pressure difference on the pressure switch. The switch-on pressure should be about 10 % higher than the pressure of the compensation tank...

Summary

Introduction

Safety instructions

In general

General safety precautions for pump installation and use.

Marking of safety instructions

Explanation of warning symbols and labels in the manual.

Residual risks

Identification of potential hazards due to pump design.

Storage and transport

Designated purpose

Intended use

Applications for which the pump set is designed.

Non-intended use

Prohibited uses and materials for the pump set.

Technical details; Operating limits

Installation

Assembly

Information on the pre-assembled state and warranty conditions.

Requirements on the borehole

Criteria for the borehole suitable for pump installation.

Installing the pump set

Procedures for physically installing the pump into the borehole.

Electrical installation

Circuit diagram

Visual representation of the electrical circuit connections.

Commissioning

Maintenance

Troubleshooting

Sectional drawings

Pump

Detailed diagram of the pump's internal components.

Motor

Detailed diagram of the motor's internal components.

Declaration of Conformity

EBARA 4WN Series Specifications

General IconGeneral
Temperature Range0 - 40 °C
Series4WN Series
TypeSubmersible Pump
MaterialStainless steel
Frequency50Hz / 60Hz

Related product manuals