ebm-papst 4650 Z - User Manual

page 1 of 5
Operating manual
4650 Z
Product type, manufacturing date (calendar week/year of construction)
and if required, conformity mark can be found on the nameplate on the
product.
Please provide us with the contents of the nameplate when making
enquiries about the product.
ebm-papst St.Georgen GmbH & Co. KG
Hermann-Papst-Straße 1
D - 78112 St.Georgen
Phone: +49 (0) 7724 / 81-0
Fax: +49 (0) 7724 / 81-1309
info2@de.ebmpapst.com
www.ebmpapst.com
As per: 16.08.2012
Version 1 1
Article number: 9244014801
Original operating manual
INDEX
1 SAFETY REGULATIONS AND INFORMATION 1
2 INTENDED USE 2
3 TECHNICAL DATA 3
4 CONNECTION AND COMMISSIONING 3
5 FAULTS, POSSIBLE CAUSES AND REMEDIES 4
6 APPROVALS 4
1 SAFETY REGULATIONS AND INFORMATION
Read the operating manual carefully before commencing work at the
product. Pay attention to the following warnings to avoid risk to
persons or malfunctioning.
This operating manual is an integral part of the product.
In the event of resale or change of ownership the operating manual
must accompany the product. This operating manual may be copied
and provided as information on potential risks and their avoidance.
Hazard classification of warning notices
The following risk ratings are used in this operating manual to denote
potential risk situations and important safety instructions:
DANGER
This is a potentially dangerous situation
and warns of an impending health risk
or risk of fatal injury if this warning is
not observed. Observe this warning.
WARNING
The dangerous situation can occur and
can result in major or fatal injuries if the
warning is not observed. Work with
extreme care.
CAUTION
The dangerous situation can occur and
can result in minor injuries or damage
to property if the warning is not
observed.
NOTE
A potentially dangerous situation can
occur and results in damage to
property if not avoided.
Qualification of personnel
Only skilled electricians are permitted to install the product, to carry out
the test run and to work at the electrical unit.
Only instructed and authorized skilled personnel are permitted to
transport, unpack, operate and service the product.
Basic safety regulations
Safety risks related to the product must be reassessed after installing
in the final device.
The operating manual was developed in accordance with European
market requirements and may need adapting to the market
requirements of the country in question.
When working at the product, observe the following:
 Do not make any changes to the product.
WARNING
Impermissible high load
 Stop the product immediately after
impermissible loading (e.g. impact,
heat, overvoltage).

Summary

Safety Regulations and Information

Hazard Classification of Warning Notices

Explains risk ratings (DANGER, WARNING, CAUTION, NOTE) used for safety instructions.

Qualification of Personnel

Specifies that only skilled electricians and instructed personnel should work on the product.

Basic Safety Regulations

General safety rules, including reassessing risks after installation and observing manual.

Impermissible High Load Warning

Warns to stop the product immediately after impermissible loading like impact or overvoltage.

Intended Use

Transport

Instructions for transporting the product in original packaging, considering vibration and climate.

Storage

Guidelines for storing the product in a dry, clean, and well-protected environment.

Cleaning

Instructions for cleaning the product using a moist cloth without pressure on the rotor.

Disposal

Advises to observe all relevant country requirements and regulations for product disposal.

Prohibited Uses

Lists prohibited uses that can be dangerous, like conveying abrasive or inflammable materials.

Technical Data

Ambient Conditions

Specifies permitted ambient temperature ranges for transport, storage, and operation.

Vibration and Shock Load

Details vibration and shock load limits for stationary operation and transport.

Connection and Commissioning

Connect Mechanical Parts

Provides caution for handling during mounting and removing the product from packaging.

Connect Electrical Parts

Emphasizes safety precautions when connecting electrical parts, including de-energizing lines.

Ground Fault Interrupter (GFI)

Specifies that only current-sensitive GFIs (type B) are permissible for personal protection.

Check Connections

Instructions for checking the product for damage and operability before switching on.

Faults, Possible Causes, and Remedies

Motor Not Rotating

Describes mechanical blocking or mains voltage faults as causes for the motor not rotating.

Motor Overheating

Discusses causes like winding interruption or high ambient temperature for an overheating motor.

Impeller Imbalance

Points to unbalance of rotating parts as a cause for impeller issues.

Approvals

Technical Safety Inspection

Outlines checks, how to check, and frequency for technical safety inspections.

ebm-papst 4650 Z Specifications

General

Model	4650 Z
Manufacturer	ebm-papst
Category	Fan
Dimensions	119 x 119 x 38 mm
Voltage	230 V
Frequency	50/60 Hz
Current	0.09 A
Impeller Material	Plastic
Bearing Type	Ball Bearing
Protection Class	IP20
Housing Material	Aluminum