◾ If you are approached, stop the motor and cutting unit.
◾ Warn the operator of the danger of blade thrust
(only using with 3-teeth blade).
◾ Blade thrust may occur when the spinning blade
contacts an object that it does not immediately cut.
◾ Blade thrust can be violent enough to cause the unit
and/or operator to be propelled in any direction, and
possibly lose control of the unit.
◾ Blade thrust can occur without warning if the blade
snags, stalls or binds.
◾ Blade thrust is more likely to occur in areas where it
is difcult to see the material being cut.
◾ Do not attach any blade to a unit without proper
installation of all required parts. Failure to use the
proper parts can cause the blade to y off and
seriously injure the operator and/or bystanders.
Discard blades that are bent, warped, cracked,
broken, or damaged in any way. Use a sharp blade.
A dull blade is more likely to snag and thrust (only
using with 3-teeth blade).
◾ The battery pack shall be disposed of safely.
◾ A coasting blade/line can cause injury while it
continues to spin after the motor is stopped or
trigger is released. Maintain proper control until
the blade/line has completely stopped rotating.
◾ Do not charge the battery pack in rain, or in wet
locations.
◾ Use only with EGO’s battery packs and chargers listed
below:
BATTERY PACK
CHARGER
BA1120E, BAX1300, BA2240E,
BA2800, BA3360, BA4200
CH2100E
CH5500E
◾ The battery pack must be removed from the
appliance before it is scrapped.
◾ Do not dispose of the battery in a re. The cells may
explode. Check with local codes for possible special
disposal instructions.
◾ Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause damage to the
eyes or skin. It may be toxic if swallowed.
◾ Exercise care in handling batteries in order not
to short the battery with conducting materials
such as rings, bracelets, and keys. The battery or
conductor may overheat and cause burns.
◾ Replacement parts - When servicing, use only
identical EGO replacement parts. Use of any other
accessory or attachment may increase the risk of injury.
◾ Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
even when the tool is not operating. Take care when
performing maintenance or service.
◾ Remove or disconnect battery pack before
servicing, cleaning or removing material from the
brush cutter.
◾ Do not wash with a hose; avoid getting water in
motor and electrical connections.
◾ If situations occur that are not covered in this
manual, use care and good judgment. Contact the
EGO Customer Service Center for assistance.
SAVE THESE INSTRUCTIONS!
SPECIFICATIONS
Cutting unit Trimmer head
3-teeth metal
blade
Voltage
56 V
56 V
No-load Speed 4500-6000 /min 4500-6000 /min
Cutting Line Type
2.4mm nylon
twist line
/
Cutting blade / ABB1203
Cutting Width 38 cm 30 cm
Weight (without battery
pack)
4.35 kg 4.64 kg
Measured sound
power level L
WA
94.80 dB(A)
K=1.01 dB(A)
94.04 dB(A)
K=1.71 dB(A
Sound pressure level at
operator’s position L
PA
80.2 dB(A)
K=2.5 dB(A)
80.0 dB(A)
K=4.1 dB(A)
Guaranteed sound
power level L
WA
(measured according
to 2000/14/EC)
96 dB(A) 96 dB(A)
Valuation of
vibration a
h
Left
handle
2.28 m/s
2
K=1.5 m/s
2
1.55 m/s
2
K=1.5 m/s
2
Right
handle
2.38 m/s
2
K=1.5 m/s
2
1.88 m/s
2
K=1.5 m/s
2
◾ The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another;
◾ The declared vibration total value may also be used in
a preliminary assessment of exposure.
NOTICE: The vibration emission during actual use of the
power tool can differ from the declared value in which the
tool is used; In order to protect the operator, user should wear
gloves and ear protectors in the actual conditions of use.
To Next Page
Loading...
Need help?
General
