EasyManua.ls Logo

EINHELL 45.014.31 - User Manual

EINHELL 45.014.31
152 pages
Go to English
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Bedienungsanleitung
Motor-Kettensäge
Operating Instructions
Gas Chain Saws
Mode d’emploi
Tronçonneuses à essence
Manual de instrucciones
Sierras de Cadena de Gasolina
Brukerveiledning
Benzin Kædesav
Istruzioni per l’uso della
Motosega a catena
Naputak za upotrebu
Motorna lančana pila
Bruksanvisning
Motorsåg
Käyttöohje
Moottoriketjusaha
Kullanma talimat∂
Motorlu Testere
Návod k použití
Řetězová motorová pila
Navodila za uporabo
MOTORNA VERIŽNA ŽAGA
Art.-Nr.: 1198124
EH-Art.-Nr.: 45.014.31 I-Nr.: 01015
MKS 38/41
Anleitung MKS 38-41 SPK 7 02.09.2005 9:15 Uhr Seite 1

Table of Contents

Questions and Answers

  • M
    Mark CoxAug 12, 2025
    Why won't my EINHELL Chainsaw start?
    • M
      mjohnsonAug 12, 2025
      Your EINHELL Chainsaw might not start due to incorrect starting procedures, an incorrectly adjusted carburetor mixture, a fouled spark plug, a plugged fuel filter, or an altered distance between the rotor and the ignition coil. Refer to the User Manual for correct starting procedures. If that doesn't help, have the carburetor adjusted by an Authorized Service Center, clean/gap or replace the spark plug, replace the fuel filter, or arrange for an authorized Customer Service workshop to adjust the distance between the rotor and the ignition coil to 0.3-0.4 mm.
  • A
    Annette JacksonAug 16, 2025
    What to do if my EINHELL 45.014.31 Chainsaw won’t start?
    • E
      Erica Trevino MDAug 16, 2025
      If your EINHELL Chainsaw won't start or starts but won't continue running, several factors could be at play. First, ensure you are following the correct starting procedures as outlined in the User Manual. A fouled spark plug could also be the culprit; try cleaning, gapping, or replacing it. Additionally, a plugged fuel filter can prevent the engine from running, so consider replacing it. If the distance between the rotor and the ignition coil has changed, arrange for an authorized Customer Service workshop to adjust the distance between the rotor and the ignition coil to 0.3-0.4 mm. Finally, the carburetor mixture adjustment setting may be incorrect, and you should have it adjusted by an Authorized Service Center.
  • C
    Cynthia RodriguezAug 23, 2025
    Why does my EINHELL Chainsaw start but have low power?
    • C
      Christopher AndersonAug 23, 2025
      If your EINHELL Chainsaw starts but the engine has low power, there are several possible causes. First, check the choke lever position and ensure it is set to the RUN position. A dirty spark arrester screen can also reduce engine power, so replace the spark arrester screen. Additionally, a dirty air filter can restrict airflow, so remove, clean, and reinstall the filter. Finally, an incorrect carburetor mixture adjustment setting may be the cause and you should have it adjusted by an Authorized Service Center.
  • A
    Alexandra EdwardsAug 27, 2025
    Why does my EINHELL 45.014.31 Chainsaw smoke excessively?
    • T
      Tyler WebsterAug 27, 2025
      Excessive smoke from your EINHELL Chainsaw may be due to an incorrectly adjusted carburetor mixture or an incorrect fuel mixture. Have the carburetor adjusted by an Authorized Service Center and ensure you are using properly mixed fuel (40:1 mixture).
  • J
    Joshua OconnorAug 31, 2025
    Why does my EINHELL 45.014.31 Chainsaw engine hesitate and has no power under load?
    • S
      Spencer ColemanAug 31, 2025
      If your EINHELL Chainsaw engine hesitates and lacks power under load, it may be due to an incorrectly adjusted carburetor mixture setting. Have the carburetor adjusted by an Authorized Service Center.
  • A
    Angela RaySep 3, 2025
    What to do if my EINHELL 45.014.31 runs erratically?
    • K
      katherinesanchezSep 3, 2025
      If your EINHELL Chainsaw runs erratically, it could be due to an incorrectly gapped spark plug. Clean/gap or replace the spark plug.
  • R
    Rachel CarpenterSep 7, 2025
    Why is my EINHELL 45.014.31 smoking excessively?
    • B
      Brittany CampbellSep 7, 2025
      If your EINHELL Chainsaw smokes excessively, the issue might stem from an incorrect carburetor mixture adjustment setting, which requires adjustment by an Authorized Service Center. Another potential cause is an incorrect fuel mixture. Ensure you are using properly mixed fuel at a 40:1 mixture.
  • T
    Tyler HughesSep 10, 2025
    What to do if my EINHELL 45.014.31 Chainsaw engine has low power?
    • W
      wshawSep 12, 2025
      If your EINHELL Chainsaw starts but has low power, it could be due to the incorrect lever position on the choke, a dirty spark arrester screen, a dirty air filter, or an incorrectly adjusted carburetor mixture. Move the choke lever to the RUN position, replace the spark arrester screen, remove, clean and reinstall the air filter, or have the carburetor adjusted by an Authorized Service Center.

EINHELL 45.014.31 Specifications

General IconGeneral
BrandEINHELL
Model45.014.31
CategoryChainsaw
LanguageEnglish

Related product manuals