EasyManua.ls Logo

EINHELL GC-LC 18/20 Li T - User Manual

EINHELL GC-LC 18/20 Li T
58 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
GC-LC 18/20 Li T
Art.-Nr.: 3410583 I.-Nr.: 21012
7
EN Operating instructions
Cordless Pole Chain Saw
FR Mode d’emploi
Scie à chaîne à perche
SP Manual de instrucciones
Motosierra inalámbrica de altura
Anl_GC_LC_18_20_Li_T_SPK7_USA.indb 1Anl_GC_LC_18_20_Li_T_SPK7_USA.indb 1 02.12.2022 08:24:2602.12.2022 08:24:26

Table of Contents

Questions and Answers

  • S
    Shannon BuckJul 29, 2025
    What to do if my EINHELL GC-LC 18/20 Li T Pole Saw chain/guide bar is hot?
    • D
      Derek HaysJul 30, 2025
      If the chain or guide bar of your EINHELL Pole Saw is getting hot, it could be due to several reasons. First, check if there's enough oil in the tank and top it up if needed. A blocked vent in the oil tank cap can also cause this, so clean the cap. Additionally, make sure the oil nozzle isn't blocked and clear it if necessary. If the chain is blunt, re-sharpen or replace it. Lastly, check the chain tension and adjust if it's overtensioned.
  • M
    Mrs. Lisa MorganAug 8, 2025
    What to do if my EINHELL GC-LC 18/20 Li T Pole Saw chain is dry?
    • C
      Charles MuellerAug 9, 2025
      If the chain on your EINHELL Pole Saw is dry, there might be no oil in the tank, so top it up with oil. Another cause could be a blocked vent in the oil tank cap, in which case you should clean the oil tank cap. Also, the oil nozzle might be blocked, so clear the oil nozzle.
  • D
    Dana KennedyAug 18, 2025
    Why EINHELL GC-LC 18/20 Li T Pole Saw judders, vibrates or does not saw properly?
    • D
      Dale TaylorAug 18, 2025
      If your EINHELL Cordless Pole Saw is juddering, vibrating, or not sawing properly, the chain might be undertensioned. Adjust the chain tension to resolve this. Alternatively, the chain could be blunt, so re-sharpen or replace it. A worn chain can also cause these issues, so consider replacing it. Finally, ensure the saw teeth are pointing in the correct direction; if not, refit the chain accordingly.

Summary

Safety Information

General Safety Precautions

Key safety rules for operating electrical tools, covering work area, personal protective equipment, and general conduct.

Battery Pack Safety Guidelines

Charger and Power Tool Safety

Power Tool Use and Care

Guidelines for safe and effective usage, maintenance, and handling of power tools to ensure longevity.

Battery Tool Use and Care

Charging Process and Environmental Protection

Battery Disposal and Chain Saw Safety

Product Overview and Specifications

Pre-Operation Checks and Assembly

Installing the Shoulder Strap

Step-by-step instructions for attaching and adjusting the shoulder strap for comfortable tool handling.

Pole Chain Saw Assembly and Adjustments

Saw Chain Lubrication

Guidance on filling the oil tank and ensuring proper lubrication for the saw chain to prevent damage.

Battery Management and Operation

Putting On the Shoulder Strap

How to correctly wear and adjust the shoulder strap for comfortable and safe tool handling.

Usage Techniques and Safety

Kickback Prevention

Explanation of kickback, its causes, and how to prevent it for operator safety during use.

Cleaning and Maintenance Procedures

Pole Chain Saw Maintenance

Specific maintenance tasks, including chain/bar replacement, lubrication system checks, and chain sharpening.

Disposal and Recycling

Storage and Transport Guidelines

Troubleshooting Common Issues

EINHELL GC-LC 18/20 Li T Specifications

General IconGeneral
Power SourceBattery
Battery Voltage18 V
Bar Length20 cm
Chain Speed5 m/s
TelescopicYes
Cutting Length200 mm
Recommended Cutting Diameter150 mm

Related product manuals