EasyManua.ls Logo

EINHELL GE-LM 36/4in1 Li-Solo - User Manual

EINHELL GE-LM 36/4in1 Li-Solo
90 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
GE-LM 36/4in1 Li
Art.-Nr.: 3411325 I.-Nr.: 21011
7
EN Original operating instructions
Cordless Telescoping Pole Chain
Saw + Hedge Trimmer + String
Trimmer + Brush Cutter
SP Manual de instrucciones original
Motosierra inalámbrica de altura +
bordeadora de arbustos +
bordeadora de hilo + desbrozadora
FR Traduction du mode d’emploi
d’origine
Scie à chaîne à manche télesco-
pique sans cordon + taille-haie
sans cordon +taille-bordures +
débroussailleuse
p
i
ne
à
chaîne à manche télesco
-
sans cordon + ta
i
lle-ha
i
e
c
or
do
n
+t
a
i
ll
e-
bord
es
+
u
ss
ailleu
s
e
Anl_GE_LM_36_4in1_Li_SPK7_USA.indb 1Anl_GE_LM_36_4in1_Li_SPK7_USA.indb 1 29.09.2021 09:33:3829.09.2021 09:33:38

Table of Contents

Questions and Answers

  • K
    Kevin ColonJul 28, 2025
    Why is the chain/guide bar on my EINHELL GE-LM 36/4in1 Li-Solo Pole Saw hot?
    • B
      Brittany NixonJul 29, 2025
      If the chain or guide bar on your EINHELL Pole Saw is getting hot, it could be due to several reasons. First, check if there's enough oil in the tank and top it up if needed. A blocked vent in the oil tank cap can also cause this issue, so clean the cap. Additionally, clear any blockage in the oil outlet. If the chain is blunt, re-sharpen or replace it. Lastly, check the chain tension and adjust if it's overtensioned.
  • V
    vkellyAug 8, 2025
    What to do if the saw chain on my EINHELL GE-LM 36/4in1 Li-Solo Pole Saw is dry?
    • R
      raymond14Aug 8, 2025
      If the saw chain on your EINHELL Pole Saw is dry, it could be due to a few reasons. First, check if there is oil in the tank and top up with oil if necessary. Also, the vent in the oil tank cap might be blocked, so try cleaning the oil tank cap. Finally, the oil outlet could be blocked, so clear the oil outlet.
  • K
    Katelyn GonzalezAug 18, 2025
    Why does my EINHELL GE-LM 36/4in1 Li-Solo judder or vibrate?
    • U
      ushortAug 18, 2025
      If your EINHELL cordless telescoping pole chain saw judders, vibrates, or doesn't saw properly, the chain might be undertensioned. Adjust the chain tension. Another reason could be that the chain is blunt, in which case you should re-sharpen or replace the chain. If the chain is worn, replace it. Finally, ensure the saw teeth point in the correct direction and refit the chain if necessary.

Summary

Safety Information

General Safety Guidelines

Essential safety rules for operating the equipment and its components.

Power Tool Operation Safety

Comprehensive safety advice for power tool operation, electrical, and personal safety.

Product Overview and Specifications

Layout, Contents, and Intended Use

Identifies tool parts, lists included items, and specifies intended applications.

Technical Data and Risks

Provides technical details and highlights potential hazards of the equipment.

Assembly Procedures

Main Component Assembly

Instructions for fitting grips, harnesses, and initial modules.

Attachment Assembly

Procedures for assembling string trimmer, brush cutter, and pole chain saw.

Hedge Trimmer & Battery Setup

Steps for assembling the hedge trimmer and managing the battery.

Operation and Working Techniques

Tool Operation Basics

Guidance on operating the tool, including harness use and switching on/off.

Working with Attachments

Techniques and advice for operating the string trimmer, brush cutter, and pole chain saw.

Maintenance, Disposal, and Support

Cleaning and Maintenance

Procedures for cleaning and maintaining the tool and its parts.

Disposal, Storage, and Troubleshooting

Information on disposal, storage, and troubleshooting the equipment.

Warranty and Customer Service

Details on product warranty coverage and customer service contact.

EINHELL GE-LM 36/4in1 Li-Solo Specifications

General IconGeneral
Battery Voltage36 V
Motor TypeBrushless
Blade Length200 mm
Cutting Length170 mm
TelescopicYes
Battery TypeLi-Ion
Bar Length200 mm
Chain Speed10 m/s

Related product manuals