EasyManuals Logo

EINHELL TC-SY 700 S User Manual

EINHELL TC-SY 700 S
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #34 background imageLoading...
Page #34 background image
GB
- 34 -
If material residue is deposited on the nozzle
(3) and the air cap (2), clean both parts with
solvent or water.
6.6 Transport
Carry the spray gun by the handle (9) or the
shoulder strap (17).
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
authorized after-sales service or similarly trained
personnel to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Disconnecting and cleaning the gun (Fig.
1-2, 11-15)
1. Unplug the spray gun from the mains power.
Press the trigger (5), so that the residual ma-
terial ows back into the container (12).
2. Unscrew the container (12) and empty the
residual material back into the material tin.
3. Clean the container (12) and the material
tube (11) with a bristle brush.
4. Pour solvent or water into the container.
Screw the container back on. Solvents with a
ash point above 55°C may not be used.
5. Reinsert the mains plug into the mains outlet
and turn on the paint spray gun. Set the max.
paint volume control (6) to the maximum ow
setting. Spray the solvent or water into a con-
tainer or rag, but never into the surroundings.
6. Repeat the procedure above until the clear
solvent or water exits from the nozzle (3).
7. Turn the paint spray gun o again and unplug
it from mains power.
8. Completely empty the container (12). Always
keep the container (12) free of residue and
check it for damage.
9. Use a rag soaked in solvent or water to clean
the outside of the paint spray gun and the
container (12).
10. Unscrew the air cap retaining ring (1) and
remove the air cap (2). Remove the nozzle
(3). Push the uid needle adapter (B) onto the
uid needle (13). Twist and pull to remove the
uid needle. Clean the air cap retaining ring,
air cap, nozzle and uid needle with a bristle
brush and solvent or water.
11. Remove the lter cap (16) to clean the air inlet
lter. Remove the lter and clean it by blowing
out with air. Replace the lter and screw the
lter cap onto the gun. Do not operate the gun
without the lter.
12. Reinsert the uid needle. Pull the trigger and
insert the nozzle on the uid needle. While
inserting, ensure that the pins on the sides of
the uid needle point up/down and not right/
left. Pull the trigger while placing the air cap
on the nozzle and tightly fasten the air cap
with the air cap retaining ring.
13. Ensure that the paint spray gun is completely
dry before storing it.
14. Properly dispose of residual paint and
cleaning agents in accordance with local laws
and regulations. Residual paint and solvents
must be taken to a suitable collection point. If
you are not sure, ask the local council where
the nearest collection point is.
Warning!
Never immerse the paint spray gun in water or
other liquids. The housing may only be cleaned
with a dampened rag.
Note: If you use 2-component paint, you must
clean the gun immediately. Otherwise the paint
may dry inside the gun, causing an equipment
fault.
Anl_SA_TC_SY_700_S_SPK8.indb 34Anl_SA_TC_SY_700_S_SPK8.indb 34 16.07.2018 09:00:1716.07.2018 09:00:17

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the EINHELL TC-SY 700 S and is the answer not in the manual?

EINHELL TC-SY 700 S Specifications

General IconGeneral
Capacity1 L
Hose length3.5 m
Product colorBlack, Red, White
Spray gun purposePaint
AC input voltage220-240 V
AC input frequency50 Hz
Package depth410 mm
Package width530 mm
Package height305 mm
Package weight3200 g
Weight and Dimensions IconWeight and Dimensions
Weight2290 g

Related product manuals