EasyManua.ls Logo

elco VECTRON ECO 1.34A - User Manual

elco VECTRON ECO 1.34A
28 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
11/2016 - Art. Nr. 4200 1015 7802A
............................................. 4200 1071 9302
VE1.34(A) / 50
4201 1000 4000
VE1.35 / 52A / 75
4201 1000 3900
Bedieningshandleiding
Voor de gespecialiseerde vakman
Aangeblazen oliebrander Low NOx
nl
Operating instructions
For authorised specialist
Low NOx
forced-draught fuel-oil burner
en
de, fr, it................................. 4200 1015 7702
nl, en.................................... 4200 1015 7802
de, fr, it, nl, en..................... 4200 1015 7902
VECTRON ECO 1.34 / VECTRON ECO 1.34A
VECTRON ECO 1.35 / VECTRON ECO 1.50
VECTRON ECO 1.52A / VECTRON ECO 1.75

Table of Contents

Questions and Answers

  • C
    crystalhamiltonAug 13, 2025
    What to do if the flame goes out during operation in my elco VECTRON ECO 1.34A?
    • J
      Jesse MilesAug 13, 2025
      If your Elco Burner's flame goes out during operation, first, ensure that the oil level in the tank is adequate and that all valves are open. Then, inspect the oil pressure, pump operation, coupling, filter, and solenoid valve. Verify the ignition circuit and electrode adjustment, cleaning or replacing electrodes if necessary. Also, clean or replace the flame monitor. Replace any faulty components, such as ignition electrodes, cables, the ignition transformer, nozzle, pump, solenoid valve, or the automatic combustion control unit, as needed.
  • F
    fernandezvanessaAug 17, 2025
    Why my Elco Burner does not start but there is no malfunction indicated?
    • A
      Alison WalkerAug 17, 2025
      If your Elco Burner doesn't start and the automatic combustion control unit shows no malfunction, it could be due to a drop in supply voltage or a power failure. Investigate and fix the cause of the voltage drop or power failure. If the issue persists, the control unit may be malfunctioning and should be replaced.
  • X
    xburtonAug 20, 2025
    What to do if my elco VECTRON ECO 1.34A Burner starts and then shuts down immediately?
    • B
      Bailey BoydAug 20, 2025
      If your Elco Burner starts briefly when switched on and then shuts down, the control unit may have been manually locked. Try resetting the control unit to resolve this issue.
  • N
    nathan86Aug 25, 2025
    Why does my elco VECTRON ECO 1.34A Burner start and then shut down after preventilation?
    • D
      Daniel WileyAug 25, 2025
      If your Elco Burner starts and then shuts down after pre-ventilation, it might be due to a parasitic flame during the pre-ventilation or pre-ignition phase. Inspect the ignition sparks, adjusting or replacing the electrode as necessary. Also, check and potentially replace the fuel-oil solenoid valve.
  • A
    Albert Harris Jr.Aug 28, 2025
    How to fix no heat request on Elco Burner?
    • H
      Hunter RobinsonAug 28, 2025
      If there is no heat request in your Elco Burner, the thermostats might be defective or incorrectly adjusted. Try adjusting the thermostats, and if the problem continues, replace them.
  • Y
    ygentryAug 31, 2025
    What to do if my elco Burner does not start but shows no malfunction?
    • S
      Shelly KentAug 31, 2025
      If your elco Burner doesn't start and the automatic combustion control unit shows no malfunction, it could be due to a drop in supply voltage or a power failure. You should check the cause of the voltage drop or power failure. Another possible cause is a control unit malfunction, in which case you should replace the control unit.
  • S
    Stefanie TaylorSep 4, 2025
    Why does elco Burner start and then shut down after preventilation?
    • R
      Ruben RiddleSep 5, 2025
      If the elco Burner starts and then shuts down after preventilation, it could be due to a parasitic flame during the preventilation/pre-ignition phase. You should check the ignition sparks and adjust or replace the electrode. Also, check or replace the fuel-oil solenoid valve.
  • N
    nicholasluceroSep 8, 2025
    How to fix elco Burner with no heat request?
    • H
      hfosterSep 8, 2025
      If there is no heat request for your elco Burner, the thermostats might be defective or incorrectly adjusted. Adjust the thermostats or replace them if necessary.

elco VECTRON ECO 1.34A Specifications

General IconGeneral
Brandelco
ModelVECTRON ECO 1.34A
CategoryBurner
LanguageEnglish

Related product manuals