Electrolux EDW 1003 - Fault Memory and Actuator Selection

6.14. Service function / readout of fault memory and single actuator selection:
General information Calling above-mentioned service function
w
Calling the service functions is executed in all designs
Calling the functions
resp. key arrangements analogously.
"readout of fault memory" and "single actuator selection"
w
For that you always have to use keys S0
, S1, S2 and S3
independent of their variant-depending program load.
1.
Appliance in switched-off condition
w
In the service function mode, the key S1
is ALWAYS
2. Press keys S1 and S3 simultaneously and
responsible for the function "readout of fault memory"
3. / 4. ... and switch on the appliance by ON/OFF switch S0.
and "single actuator selection".
For that keep pressed keys S1 and S3 until the 3 confirmation
LEDs LD1
, LD2 and LD3 are flashing.
(A temporary flashing up of LEDs is possible and is no fault!)
5. / 6. By actuating the function key S1 you now can call the function.
The confirmation LED LD1
continues flashing, the LEDs
LD2
and LD3 go out.
By pressing key S1
the first time the 1. fault is displayed
in a coded way via the "END" LED.
By pressing key S1
a second and third time it is possible to
read out the second and third value of the fault memory.
(see description page B 19 / "Survey of fault displays")
From pressing the key S1
the fourth time onward the LED
LD1
goes out and LD2 starts flashing.
Now you can call the single actuators one after the other.
4. Actuation: Selection of regeneration valve
5. Actuation: Selection of drain pump
6. Actuation: Selection of valve
(filling to level - if level already existing, no filling)
7. Actuation: Selection of heating
(only when level detected)
8. Actuation: Selection of circulation pump
9. Actuation: Selection of detergent dispenser
It is generally valid:
10.Actuation:
Selection of drying fan
For calling all service functions you always have first to All positions can be called scrolling as many times as one wants.
actuate function keys S1
and S3 before switching
on the appliance by ON/OFF switch S0
! The single steps are switched onward manually by pressing
The keys have to remain pressed aprox. 4 seconds a key. If the function key S1
is not pressed within 60 seconds,
to activate the function. the service function is left automatically. All LEDs of program
This procedure is intentionally different to that for the and option keys are lit. The appliance is in the "prestart" mode
customer functions. again. It is also possible to leave the function by switching off
the appliance by ON/OFF key S0
.
2.
1.
3.
S0
3-4 Sekunden
5.
LD1
S1
4.
S1 S3 S0
LD1 LD2 LD3
alle blinken
LED blinkt
pro Tastendruck
1 Weiterschaltung
S1
6.
LD1 LD2 LD3 LD4 LD5 LD6
S1 S2 S3 S4 S5 S6
LD7
LD8
LD9
LD10
LD11
LD12
S0
S0S1 S3
S1 S3
LD1
S1
LED blinkt
Anzeige 2. + 3.Fehlers
Anzeige
der Einzelaktoren
LD2
S1
LED blinkt
LD1
S1
LED blinkt
... AUS nach 60sek. automatisch
S0
LD1 LD2 LD3 LD4 LD5 LD6
S0
... AUS durch manuelle Betätigung über Ein/Aus
EDW 1003 / VGA
LD1 LD2 LD3
S1 S3
ENDE
S0
34