Why is there reduced flow from the ELGA Water Filtration Systems dispenser?
If you're experiencing reduced water flow from the ELGA Water Filtration Systems dispenser, examine the inlet water strainer. Additionally, replace the POU filter or the UF filter if your system is equipped with one. If the issue persists, it may indicate a worn pump, and you should contact Customer Services.
What to do if there is an alarm and flashing quality value on ELGA PURELAB Classic - US?
If you're experiencing an alarm and flashing quality value on your ELGA Water Filtration Systems, first mute the alarm. Verify that the alarm set value is correct. Dispense approximately 10 liters of water to drain. Inspect the UF, if fitted. If the problem continues, replace the purification pack. If the issue persists, contact Customer Services.
How to troubleshoot no display message on ELGA Water Filtration Systems?
If your ELGA Water Filtration Systems unit is not displaying any message, check the mains supply and lead to ensure they are properly connected. Make sure the mains power is switched on. Inspect the fuses in the power inlet module and replace them if they are blown.
What causes the high water temperature alarm in ELGA PURELAB Classic - US?
If you're getting a high water temperature alarm on your ELGA Water Filtration Systems, first check that the correct alarm point is set. Then, verify that the feedwater temperature hasn't suddenly increased. Dispense some water to allow colder water to be drawn into the unit.
What to do if ELGA PURELAB Classic - US Water Filtration Systems unit will not operate?
If your ELGA Water Filtration Systems unit isn't operating, ensure that the correct purification pack is properly installed. Also, check that the purification pack has a valid consumable date and that the reminder hasn't been exceeded by 12 months.
How to fix reservoir low level alarm on ELGA PURELAB Classic - US?
If you receive a Reservoir Low Level alarm on your ELGA Water Filtration Systems, mute the alarm. Ensure the unit is fed from a reservoir and that the correct feature has been set. Check the feed to the reservoir to confirm it is operational and the reservoir is filling.
How to clear purification pack change reminder alarm on ELGA PURELAB Classic - US?
If you receive a Purification Pack Change reminder alarm on your ELGA Water Filtration Systems, mute the alarm. Replace the purification pack.
How do I clear the UF change reminder alarm on ELGA PURELAB Classic - US Water Filtration Systems?
If you encounter a UF Change reminder alarm on your ELGA Water Filtration Systems, mute the alarm. Replace the UF filter.
What should I do for the UV change reminder alarm on ELGA PURELAB Classic - US Water Filtration Systems?
If you see a UV Change reminder alarm on your ELGA Water Filtration Systems, mute the alarm. Replace the UV filter.
How to fix a noisy ELGA PURELAB Classic - US Water Filtration Systems unit?
If your ELGA Water Filtration Systems unit is noisy, open the front door and secure the pipework to stop the vibration.
Lists the different PURELAB Classic models.
Explains the purpose and scope of the manual.
Safety precautions related to electrical power supply.
Safety precautions regarding UV lamp exposure.
General chemical handling and safety advice, including sanitization procedures.
Overview of the PURELAB Classic water purification unit.
Explains the water purification process for Classic DI.
Details feedwater, dimensions, electrical, user interface, safety, and operational specs.
Defines the icons used on the control panel.
Lists the items included with the unit.
Guidelines for unit positioning and environment.
Instructions for connecting water inlet and drain tubes.
Comprehensive guide to initial controller setup, including menus, settings, and alarms.
Instructions for changing password and resetting consumable timers.
Steps for initial startup, including water supply, by-pass, and purification pack installation.
Guide for installing and bleeding the Point-Of-Use filter.
Explains the unit's recirculation mode.
Steps to dispense water manually.
Step-by-step guide to replace the purification pack.
Instructions for removing and fitting the Ultrafilter.
Step-by-step instructions for replacing the UV lamp.
Guide for removing, replacing, and bleeding the POU filter.
Procedure for sanitizing the unit using EfferSan™™ tablets.
Procedure for sanitizing the unit using Minncare Cold Sterilant.
Defines the icons used on the control panel.
Lists alarm conditions and associated icons.
Details replacement timers for components.
General| Brand | ELGA |
|---|---|
| Model | PURELAB Classic - US |
| Category | Water Filtration Systems |
| Language | English |
To Next Page