Elinchrom ELC Pro HD User Manual

345
6
7
8
1
2
1
2
3
4
5
6
7
8
Setting title
Modelling lamp status
Back to dashboard
Visual Flash Confirmation function
Proportional modelling lamp setup
Proportional modelling lamp value
Visual Flash Confirmation status
Modelling lamp power in f-stop
statistics
4
5
6
7
8
9
101112
13
14
1
2 3
EL-Skyport synchronisation speed
EL-Skyport Frequency channel
EL-Skyport Group number
Photocell status
Ready beep
Power in J
Flash duration in s
Flash function
Flash function value
Increase 1 f-stop
Open flash test
Decrease 1 f-stop
Recycling mode
Power in f-stop equivalent
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
345
Left
(L)
Right
1
2
3
4
5
Menu title
Menu selected
Menu exit (back to dashboard)
Enter
Back
(L)
(R)
(S)
(R)
(S)
(L)
(R)
(S)
Set
modeling lamp
power
1° level 2°level 3° level
DISPLAY DESCRIPTION
GREEN ready
GREEN BLINKING discharging
ORANGE charging
RED BLINKING flashing before 100% ready
RED BREATHING standby
prop
free
VFC (Visual Flash Control)
Proportional modelling lamp Mode
off
-0.5 to -2.0 f-Stop
ON OFF
modeling lamp button
short press
long press
L button
S Knob button
Knob button (
S)
Standby
ON
OFF
L button save
S button load
User Preset preset1-4
DISPLAY PANEL - DASHBOARD
DISPLAY PANEL - MAIN MENU
DISPLAY PANEL - MODELING LAMP
KNOB COLOR INFO
photocell
off/on
auto
preflash
preflash setup manual block time timeframe
off (r0)
normal (r1)
speed (r2)
group 1 to 4
skyport (radio)
group
channel 1 to 8
channel
power settings
standby
auto off
from[off] to [60min] in steps of 5 min
from[off] to [10hrs] in steps of 1 hour
recycling time
default fast slow
audio
beep volume
Tone (0 to 7)beep tone
key click
off low default high
max
off low
min default high max
flash mode
unit index
set delay (in ms)
frenquency
sequence
delayed
strobo
total units
seq. timeout
duration
default
Setup of activated modesetting

Elinchrom ELC Pro HD Specifications

General

Brand	Elinchrom
Model	ELC Pro HD
Category	Lighting Equipment
Language	English

Summary

Display Panel Dashboard Features

Power Output (Joules)

Increase 1 f-Stop

Decrease 1 f-Stop

Power Output (f-Stop)

Display Panel Modeling Lamp Settings

Proportional Modeling Lamp Setup

Proportional Modeling Lamp Value

Modeling Lamp Power (f-Stop)

EL-Skyport Transmitter Speed Controls

Error Management and Solutions

Capacitor Over Voltage Error

Error related to capacitor overvoltage. Requires unit restart.

Overheat Error

Indicates the unit has overheated. Wait for cooling.

Discharge Error

Error during the discharge process. Requires service.

Charge Timeout Error

Error when charging exceeds timeout. Requires service.

Zero Detect Fault Error

Error in zero detection. Requires service.

Charge Hold Error

Error during charge hold. Requires service.

Fan Error

Error related to the cooling fan. Requires service.

High Supply Voltage Error

Error due to excessively high supply voltage. Check supply.

Low Supply Voltage Error

Error due to insufficient supply voltage. Check supply.

Under Voltage During Charge Error

Error from low supply voltage during charging. Check supply.

Over Current Detection Error

Error indicating overcurrent. Requires service.

Heat Sink Sensor Error

Error: Heat Sink temperature sensor disconnected. Requires service.

Front Sensor Error

Error: Front temperature sensor disconnected. Requires service.

Charge Sensor Error

Error: Charge temperature sensor disconnected. Requires service.

Power Board Connection Error

Error: Power board not connected or found. Requires service.

Capacitor Voltage Symmetry Error

Flash Tube Afterglow Error

Auto Ignition Charge Error

Auto Ignition Ready Error