Eltax AVR-800 - User Manual

Other manuals for Eltax AVR-800

Service Manual32 pages

Questions and Answers

M
Miss Sierra ForbesAug 17, 2025
What to do if the Eltax Receiver remote control is not working?
- A
  ambergarrisonAug 17, 2025
  If the remote control for your Eltax Receiver isn't working, first, replace the batteries with new ones. If that doesn't solve the issue, make sure you are operating the remote control within its effective range of the receiver.
Y
ymyersAug 20, 2025
Why is there sound only from one channel on my Eltax Receiver?
- J
  Joseph PrinceAug 20, 2025
  If sound is only coming from one channel on your Eltax Receiver, it could be due to a disconnected input cord. Ensure that all input cords are securely connected. Also, check the BALANCE control and adjust it, as it might be set to one side.
A
astephensAug 23, 2025
What to do if the Eltax Receiver sound cuts off during music or has no sound even when powered on?
- C
  Courtney OwenAug 23, 2025
  If the sound cuts off or there's no sound from your Eltax Receiver even when it's powered on, the speaker impedance might be too low. Turn off the power, then turn it back on, reduce the volume, or switch to the correct 8 ohm speakers.
T
Timothy SullivanAug 26, 2025
Why is there no sound from the front speaker of my Eltax Receiver?
- M
  Michael ReedAug 26, 2025
  If there's no sound from the front speaker of your Eltax Receiver, ensure the 'short pin' is inserted into the EQ jack. Also, if speakers A and B are selected simultaneously, but speaker B is not connected, connect both speakers or select speaker A only.
M
matthewsimpsonAug 28, 2025
How to troubleshoot low bass response on Eltax Receiver?
- T
  Tanner MaxwellAug 28, 2025
  To troubleshoot low bass response on your Eltax Receiver, check all speakers to ensure they have the correct polarity (+/–).
F
floydmariaAug 31, 2025
Why is there no sound from the surround speakers of my Eltax Receiver?
- P
  Paul PageAug 31, 2025
  If there's no sound from the surround speakers on your Eltax Receiver, first, check that the SURROUND ON/OFF button is set to the desired surround mode. Second, ensure that the source being played is recorded or broadcast in surround sound or stereo. Finally, check all rear speaker wires for a good connection.
B
Beth MunozSep 2, 2025
Why is there no sound from the center speaker of my Eltax Receiver?
- C
  carlwelchSep 2, 2025
  If there is no sound from the center speaker of your Eltax Receiver, ensure that the SURROUND mode button is set to DOLBY DIGITAL, DTS, DOLBY PRO LOGICII or 3 STEREO.
K
kevin32Sep 5, 2025
Why is there no sound from the surround back speaker on my Eltax Receiver?
- M
  Megan KennedySep 5, 2025
  If there's no sound from the surround back speaker on your Eltax Receiver, check that the surround back speaker cable is connected correctly. Also, ensure that the surround mode is set to EX/ES and that 'Surround back = NONE' has not been selected in the SPEAKERS Configuration; make the correct setting if needed.
M
Mark MorseSep 8, 2025
What causes a hissing noise when listening to Eltax Receiver in stereo?
- R
  raymondmiguelSep 8, 2025
  A slight hissing noise might be heard when listening to FM stereo broadcasts on your Eltax Receiver because the modulation method differs from monaural broadcasts. You can try reducing the treble sound by adjusting the treble controls, changing the antenna's location, height, or direction. Setting the FM mode to monaural via the STEREO/MONO button will eliminate the noise but result in monaural sound. If using an indoor antenna, switch to an outdoor antenna or try an antenna with more elements.
K
Kevin JohnsonSep 12, 2025
Why do left and right speakers sound reversed on my Eltax Receiver?
- T
  Timothy FernandezSep 12, 2025
  If the left and right speakers sound reversed when listening to music in stereo on your Eltax Receiver, it's likely that the speakers are connected incorrectly. Check the speaker connections and reconnect them if needed.