Eltek Valere Minipack User Manual

Quick Start Guide Minipack PS System 356808.103, 1v2-2008-10
24
CAN Bus Nodes
The CAN Bus Nodes are control units connected to the power system’s CAN bus. They have a
rugged sealed-plastic design, with DIN-rail or Velcro tabs as standard mounting options.
When the CAN bus address is configured and the unit connected to the bus, it will automatically
communicate with the Smartpack controller (“plug and play”). Configure then the CAN node
functionality using PowerSuite.
Battery Monitor CAN Node
The Battery Monitor CAN Bus Node enables you to decentralize and increase the number of battery
symmetry measurements in your Smartpack based DC power supply system. Also, it monitors the
battery compartment temperature – using the built-in sensor – the battery fuse – with a fuse
monitoring input – and the battery current – via a current sense input.
Read also the “Installation Guide Battery Monitor CAN Node”, document 351507.033.
Appendix CAN Bus Nodes
CAN port 1&2
Electricall
y
identical
DIP switches
CAN ID address
DIP switch #1
Battery Monitor
Battery Monitor
Monitor Inputs
Terminal Block
Powe
r
LED Lamp
(
g
reen
)
Warning
LED Lamp
(
y
ellow
)
Pin 1
Pin 8
A
larm
LED Lamp
(
red
)
Batter
y
Monitor Connections
Part 242100.300
FUNCTION SIGNAL PIN-OUT
4
3
2
1
5
8
7
6
X:*
(From the
batteries)
Built-in Battery
Temperature Sensor
Battery
Monitor
From previous CAN
bus node
Batt. Symmetry 1
+
−
Batt. Fuse
CAN port 1&2
RJ45, 8 pins
+
+
+
+
Batt. Symmetry 2
Batt. Symmetry 3
Batt. Symmetry 4
+
−
Batt. Current
1.
5
mm
2
, max.
wire section
To next CAN bus node
(From the current shunt)
(From the current shunt)
O
r
RJ45 CAN bus
termination plug,
if the Battery
Monitor is the
last node in the
CAN bus
Battery
Monitor
ID
#
DIP Switch Position
1 ⎯ 2 ⎯ 3 ⎯ 4
1
s
t
Monitor 33
OFF
⎯
OFF
⎯
OFF
⎯
OFF
2
nd
Monitor 34
ON
⎯
OFF
⎯
OFF
⎯
OFF
3
rd
Monitor 35
OFF
⎯
ON
⎯
OFF
⎯
OFF
4
th
Monitor 36
ON
⎯
ON
⎯
OFF
⎯
OFF
5
th
Monitor 37
OFF
⎯
OFF
⎯
ON
⎯
OFF
6th Monitor 38
ON
⎯
OFF
⎯
ON
⎯
OFF
7
th
Monitor 39
OFF
⎯
ON
⎯
ON
⎯
OFF
8
th
Monitor 40
ON
⎯
ON
⎯
ON
⎯
OFF
9
th
Monitor 41
OFF
⎯
OFF
⎯
OFF
⎯
ON
10
th
Monitor 42
ON
⎯
OFF
⎯
OFF
⎯
ON
11
th
Monitor 43
OFF
⎯
ON
⎯
OFF
⎯
ON
12
th
Monitor 44
ON
⎯
ON
⎯
OFF
⎯
ON
13
th
Monitor 45
OFF
⎯
OFF
⎯
ON
⎯
ON
14
th
Monitor 46
ON
⎯
OFF
⎯
ON
⎯
ON
Battery Monito
r
DIP switch configuration
ID <33>
(All switches OFF)
Note:
• The
monitor’s
ID #
corresponds
to the DIP
switch’s
binary value
plus 33

Eltek Valere Minipack Specifications

General

Brand	Eltek Valere
Model	Minipack
Category	Power Supply
Language	English