1
INSTALLATION
FSP300-4W
FILTER & PUMP COMBO
INSTALL/START-UP OF FILTRATION
* Install filtration system including pump, filter tank and excessive shock.
multiport valve. d.Carefully pour in correct amount and grade of filter sand. Be
* The filter system should be installed as close as possibie to sure center pipe remains centered in opening.
the swimming pool and preferably at a level of 0.50 Sand surface should be leveled and should come to about
metres below the surface of the water in the swimming the middle of the filter tank. Remove plastic cap from internal
pool. Make sure there is drainage available at the place pipe.
where the filter is to be installed. 2.Assemble filter control valve to filter tank.
* PUMP a.Insert filter control valve(with O'ring in place)into the tank
1.Only qualified, licensed personnel should install pump neck, taking care that the center pipe slips into the hole in the
and wiring. bottom of the valve.
2.Electrical Contractors Please Note: All 220V/60Hz pump b.Place two plastic clamps around valve flange and tank neck
must be wired to the main power supply trough an and tighten just enough so that the valve may Be rotated on
approved and correctly rated contractor. tank for final positioning.
3.Allow for gate valve in suction piping. c.Carefully screw pressure gauge(with O'ring in place)into
4.Pump suction and discharge connections have moulded tapped hole in valve body. Do not over-tighten.
in thread stops, do not try to screw pipe in beyond these d.Connect pump to control valve opening marked IN with hose.
stops. After connections are made, tighten clamps with screwdrive,
* FILTER TANK and MULTIPORT VALVE tapping around clamp with screwdrive handle to help seat
1.Loading the sand media. Filter sand media is loaded valve flange clamp.
through the top opening of the filter. 3.Make return to pool pipe connection to control valve opening
A. Loosen the plastic clamps from tank neck. marked OUT and complete other necessary plumbing
b.Cap internal pipe with plastic cap to prevent sand from connections, suction lines to pump, waste, etc.
entering it. 4.To prevent water leakage, be sure all pipe connections are
c.We recommend filling tank approximately 1/2 way with tight.
water to provide a cushion effect when the filter sand is
poured in. This helps protect the under-drain laterals from
1. Be sure correct amount of filter media sand is in tank FILTER position and restart pump. The filter is now operating
and that all connections have been made and are in the normal filter mode, filtering dirt particles from the
secure. pool water.
2. Depress control valve handle and rotate to BACKWASH 5. Adjust pool suction and return valves to achieve desired
position. (To prevent damage to control valve seal, flow. Check system and filter for water leaks and tighten
always depress handle before turning.) connections, bolts, nuts, as required.
3. Prime and start pump. Never run pump dry! Running 6. Note the initial pressure gauge reading when the filter is
pump dry may damage seals, causing leakage and clean. (It will vary from pool to pool depending upon the
flooding! Fill pump with water before starting motor. pump and general piping system.) As the filter removes
(be sure all suction and return lines are open), allowing dirt and impurities from the pool water, the accumulation
the filter tank to fill with water. Once water is flowing in the filter will cause the pressure to rise and flow to
out of the waste line, run the pump for at least 1 minute. diminish. When the pressure gauge reading is 1.5 bar,
The initial back-washing of the filter is recommended higher than the initial "clean" pressure you noted, it is time
to remove any impurities or fine sand particles in the to backwash the filter (see BACKWASH under filter and
sand media. control valve functions).
4. Turn pump off and set valve to RINSE position. Start NOTE: During initial clean-up of the pool water it may be
pump and operate until water in sight glass is clear, necessary to backwash frequently due to the unusually
about 1/2 to 1 minute. Turn pump off and set valve to heavy initial dirt load in the water.
名 称
版 本 编 号
规 格
比 例
颜 色
产品负责人
更改日期
更改内容
版本
制图/设计
A
意万仕(中山)泳池设备有限公司
EMAUX ZhongShan)Swimming Pool Equipment Co., Ltd(
审核
批准
80g印尼蓝
普通印刷
2020.12
1 : 1
210X297(mm)
EMFS20120902
PANTONE Process Black C
材 料
工 艺
日 期
EMAUX FSP300-4W 胶缸连泵(220V 60Hz) 英文说明书
EMFS20120902
To Next Page
Need help?
General
