emaux SC Series - User Manual

Questions and Answers

K
Kimberly MasonAug 15, 2025
How to troubleshoot emaux SC motor that does not start?
- J
  Jason ButlerAug 15, 2025
  If your Emaux Water Pump motor doesn't start, it could be due to several reasons. First, check the disconnect switch or circuit breaker to ensure they are in the on position. Also, inspect the fuses and reset any thermal overloads. Other potential causes include a locked motor shaft, burned-out motor windings, a faulty starting switch (for single-phase motors), disconnected or defective wiring, or low voltage. Inspect the starting switch of the motor. Make sure the voltage supply is adequate and check wiring for disconnections or defects.
J
James DeanAug 18, 2025
What to do if emaux SC Water Pump delivers no water?
- D
  Daniel AndersonAug 18, 2025
  If your Emaux Water Pump is not delivering water, the first thing to check is whether the pump is properly primed. Also, make sure that there are no closed valves in the suction or discharge lines; if there are, open them. Check for any leakage or air in the suction system. Finally, inspect the impeller for any clogs and clear them.
J
Jonathan LewisAug 21, 2025
Why is my Emaux Water Pump so noisy?
- A
  Amy SchaeferAug 21, 2025
  If your Emaux Water Pump is making excessive noise, start by cleaning the plugged basket in the skimmer or hair and lint pre-filter. Other potential causes include worn motor bearings (inspect and replace if necessary), a partly closed valve in the suction line (open it fully), a partly plugged suction line (clear any obstructions), a plugged or too-small vacuum hose (inspect and replace), or inadequate pump support (ensure proper support).
S
Sandra SandersAug 25, 2025
Why does my emaux SC have low capacity?
- A
  Anna WestAug 26, 2025
  If your Emaux Water Pump has low capacity, start by ensuring that the valve in the suction or discharge line is fully open. Check for any obstructions in the suction or discharge lines and clear them. Also, verify that the suction or discharge line is adequately sized. Clean the plugged basket in the skimmer or hair and lint pre-filter. Clean or replace the dirty sand filter. Clear any clogs from the impeller.
H
Henry StokesAug 28, 2025
What causes emaux SC Water Pump motor to overheat?
- R
  ronald27Aug 29, 2025
  If your Emaux Water Pump motor overheats and the protector trips, the issue might be due to low voltage. Check for low voltage. If you have a dual voltage model, verify that the motor windings are connected to the correct voltage. Also, ensure that there is adequate ventilation around the motor.
S
Steven SmithAug 31, 2025
How to reduce high pressure in emaux SC?
- B
  Bryan HarrisSep 1, 2025
  If your Emaux Water Pump is producing high pressure, it could be due to a discharge valve or inlet fittings being closed too much; open them. Also, ensure that the return lines are adequately sized. Clean or replace any dirty filters.
C
Christina GoodSep 4, 2025
Why emaux SC does not reach full speed?
- R
  Roberto BarberSep 4, 2025
  If your Emaux Water Pump isn't reaching full speed, it could be due to low voltage; check for that. Also, ensure that the pump is connected to the correct voltage.
A
Albert RodriguezSep 7, 2025
Why are there air bubbles at inlet fittings of my emaux SC Water Pump?
- H
  hallchristopherSep 8, 2025
  If you notice air bubbles at the inlet fittings of your Emaux Water Pump, check for air leakage in the suction line connections or valve stem. Clean the cover gasket of the hair and lint pre-filter. Ensure that the water level in the pool is adequate.
J
Jeffrey BradySep 12, 2025
What to do if there is leakage of water at the shaft of Emaux Water Pump?
- D
  dschwartzSep 12, 2025
  If you observe water leaking at the shaft of your Emaux Water Pump, it indicates that the shaft seal requires replacement. Replace the shaft seal.