Emax TINYHAWK III User Manual

Thanks for purchasing the Tinyhawk III.
Please follow the instruction manual to assemble and configure your Tinyhawk.
Design in California, Made in China

Emax TINYHAWK III Specifications

General

Battery Connector	PH2.0
Flight Time	5 minutes
Flight Controller	F4 Flight Controller
Motor	1103 10000KV Brushless Motor
Receiver	FrSky D8
Camera	700TVL Camera
VTX	25mW / 100mW Switchable VTX
Battery	450mAh
Transmitter	Compatible with FrSky D8/D16

Summary

E8 Transmitter

1.1 E8 Transmitter Overview

Diagram showing the physical layout and controls of the E8 Transmitter.

1.2 Power On and Off

Instructions for powering the E8 Transmitter on and off.

1.3 Binding and Unbinding

Steps to bind and unbind the E8 Transmitter with the Tinyhawk III.

1.4 Mode Switching

How to switch between D8, D16, and D16 LBT modes on the transmitter.

1.5 Gimbal Trim

Adjusting the gimbal trim for precise control and hovering.

1.6 Joystick Calibration

Procedure for calibrating the E8 Transmitter joysticks.

1.7 Changing Transmitter Modes

How to change the E8 Transmitter between left-hand and right-hand modes.

1.8 Trainer Port for Simulators

Using the trainer port to connect the transmitter to flight simulators.

1.9 Battery & Charging

Information on the E8 Transmitter's battery and charging process.

Transporter 2 (with DVR)

2.1 Transporter 2 Overview

Overview of the Transporter 2 goggles, including labeled components.

2.2 Power On and Off

Instructions for powering the Transporter 2 goggles on and off.

2.3 Video Channel Selection

How to manually select the correct video frequency band and channel.

2.4 Video Channel Auto Search

Using the auto search function to find the best video channel.

2.5 Turn On and Off Recording

Instructions for starting and stopping DVR recording on the Transporter 2.

2.6 Card Recording Parameter Setting

Setting parameters for recording to a TF card.

2.7 Screen Parameter Setting

Adjusting screen settings like brightness and contrast.

2.8 Battery & Charging

Information on the Transporter 2's battery and charging process.

Tinyhawk III Propeller

3.1 Tinyhawk III Components

Diagram showing the components of the Tinyhawk III drone.

3.2 Propeller Installation and Removal

Instructions for installing and removing the Tinyhawk III propellers.

Tinyhawk III VTX Settings

4.1 Tinyhawk III VTX Diagram

Diagram showing the Video Transmitter (VTX) connections on the Tinyhawk III.

4.2 Changing VTX Settings via Betaflight OSD

How to change VTX settings using the Betaflight On-Screen Display.

4.3 Setting the VTX Channel

Procedure for setting the VTX channel using the transmitter's buttons.

Other Configurations

5.1 Binding via Betaflight Configurator

Using the Betaflight CLI to put the receiver into binding mode.

Tinyhawk III Flight Control

6.1 Flight Control Diagram

Diagram of the Tinyhawk III flight controller board and its connections.

6.2 Stock Flight Controller Settings

Default flight controller settings and channel mapping for the Tinyhawk III.

6.3 PID Tuning

Information on the pre-tuned PID settings for optimal flight performance.

6.4 Adjusting Software Settings (Betaflight Configurator)

How to adjust software settings using the Betaflight Configurator.

6.5 Reprogramming Flight Controller

Steps for reprogramming the Tinyhawk III flight controller firmware.

6.6 Setting Correct Configuration

How to download and apply correct settings using a CLI dump file.

How To Fly Tinyhawk III

7.1 Lock & Unlock Controls

Procedure for locking and unlocking the transmitter controls before flying.

7.2 Flight Mode Selection

Explanation of the different flight modes (Angle, Horizon, Rate) and how to select them.

7.3 Advanced FPV Flight

Guide to flying the Tinyhawk III in First Person View (FPV) mode.