Emerson Fisher FIELDVUE DVC6200 Series User Manual

www.Fisher.com
Fisher
™
FIELDVUE
™
DVC6200 Series Digital Valve
Controllers
Contents
Before You Begin 3......................................
Step 1. Install the DVC6200 on the Valve 4...................
Step 2. Connect the Pneumatic Tubing 19...................
Step 3. Connect the Electrical Wires 23......................
Step 4. Configure the DVC6200 33.........................
Special Instructions for DVC6200 SIS 35.....................
Special Instructions for DVC6200f PST 37....................
Special Instructions for Solenoid Valve Health Monitoring 43....
Quick Start Guide
D103556X012
DVC6200 Digital Valve Controllers
July 2017
This quick start guide provides installation and initial setup information for DVC6200 Series digital valve controllers
W9713
SIS

Emerson Fisher FIELDVUE DVC6200 Series Specifications

General

Manufacturer	Emerson
Series	FIELDVUE DVC6200
Type	Digital Valve Controller
Communication Protocol	HART
Operating Temperature Range	-40 to 85 °C (-40 to 185 °F)
Enclosure Rating	NEMA 4X, IP66
Material	Aluminum, Stainless Steel
Hazardous Area Certifications	ATEX, IECEx, FM, CSA
Input Signal	4-20 mA, HART
Power Supply	Loop-powered
Supply Pressure	1.4 to 6.0 bar
Certifications	SIL3 capable
Diagnostics	Advanced Valve Diagnostics

Summary

Before You Begin

Hazardous Area Approvals

Lists approvals for CSA, FM, ATEX, and IECEx for hazardous areas.

Step 1. Install the DVC6200 on the Valve

Mounting Variations and Guidelines

Details housing types and general advice for mounting the digital valve controller.

Magnetic Tool Usage Precautions

Advises on safe use of magnetic tools near the DVC6200 magnet assembly.

Sliding-Stem Linear Actuator Installation

Covers mounting procedures for sliding-stem linear actuators, including various types and configurations.

Quarter-Turn Rotary Actuator Installation

Details mounting procedures for quarter-turn rotary actuators, both integral and bracket-mounted.

Step 2. Connect the Pneumatic Tubing

Integral Mounting Pneumatic Connections

Explains how to connect pneumatic tubing for integral mounting configurations.

Filter Regulator Connections

Details connecting filter regulators to the DVC6200 supply input.

Vent Connection

Instructions for connecting a pipe-away vent line if necessary.

Step 3. Connect the Electrical Wires

FOUNDATION Fieldbus and PROFIBUS PA Wiring

Wiring instructions for FOUNDATION Fieldbus or PROFIBUS PA communication.

HART Device Wiring

Wiring instructions for HART communication devices.

Position Transmitter or Discrete Switch Wiring

Wiring for optional 4-20 mA position transmitter or discrete switch output.

Remote Mount Feedback Unit Wiring

Instructions for wiring the DVC6205 base unit to the DVC6215 feedback unit.

Smart Wireless THUM Adapter Wiring

Wiring instructions for installing and connecting the Smart Wireless THUM Adapter.

Step 4. Configure the Digital Valve Controller

User Interface Tools and Software

Lists available software tools for instrument configuration and calibration.

Applying Pneumatic and Electrical Power

Details applying pneumatic pressure and electrical power for configuration.

Special Instructions for DVC6200 SIS

DIP Switch Configuration for SIS

Explains DIP switch settings for DVC6200 SIS operational modes.

LCP100 Connection for SIS

Describes connecting the optional Local Control Panel (LCP100) to the DVC6200 SIS.

De-Energize to Trip (DETT) DVC6200 SIS

Instructions for DETT applications without a solenoid valve.

DETT DVC6200 SIS with Solenoid Valve

Instructions for DETT applications with a solenoid valve.

Special Instructions for DVC6200f PST

Partial Stroke Testing (PST) Setup

Information on configuring the DVC6200f PST for controlled ramp tests.

Special Instructions for Solenoid Valve Health Monitoring

Solenoid Valve Health Monitoring Setup

Details tubing configurations for monitoring solenoid valve operation.

Wiring for Solenoid Valve Testing (DVC6200 SIS)

Configuration for using the DVC6200 SIS to test solenoid valves.