How to troubleshoot Emerson Rosemount 3300 when the integral display does not work?
To troubleshoot an integral display that does not work on your Emerson Transmitter, check the display configuration, loop power, and display connection.
Why is the Interface Level reported as NAN when P2 and P3 are detected on my Emerson Transmitter?
If both P2 and P3 are detected but Interface Level is reported as Not A Number (NAN) in the waveform plot of your Emerson Transmitter, set the Measurement Mode to “Level and Interface”.
What does it mean when both Level and Interface Level are reported as NAN on Emerson Rosemount 3300?
If both Level and Interface Level are reported as Not A Number (NAN) on your Emerson Transmitter, use the command “Read Gauge Status” and check if error “Probe Failure” is active. If this is the case, check the probe connection.
How to troubleshoot when P2 and P3 are detected but the interface level is equal to the product level on Emerson Transmitter?
If both P2 and P3 are detected, but the interface level is equal to the product level on your Emerson Transmitter, adjust thresholds T2 and T3.
What to do if P2 is detected but Level is incorrectly reported as Full or Empty on Emerson Rosemount 3300 Transmitter?
If P2 is detected, but the Level is incorrectly reported as Full or Empty on your Emerson Transmitter, use the command “Read Gauge Status” and check if the warning “Probe Immersed” is active. If this is the case, check that the transmitter is configured with the correct probe type and that the reference pulse (P1) is below amplitude threshold T4. If not, adjust T4 to an appropriate value.
What to do if Analog Out is set in Alarm on my Emerson Rosemount 3300?
If the Analog Out is set in Alarm for your Emerson Transmitter, use the command “Read Gauge Status” to check for active errors. Also, use the command “Read Gauge Status” and check if the error “Probe Failure” is active. If the probe failure error is active, check the probe connection.
How to fix the issue when the reference pulse is not detected by Emerson Rosemount 3300 Transmitter?
If the reference pulse is not detected by your Emerson Transmitter, check the product level, ensure that the correct probe type is configured, and verify the Amplitude Threshold T1.
Why does the level accuracy seem off on my Emerson Rosemount 3300?
If the level accuracy of your Emerson Transmitter seems off, verify the Reference Gauge Height parameter and check the status and diagnostic information.
General| Model | Rosemount 3300 Series |
|---|---|
| Category | Transmitter |
| Technology | Guided Wave Radar (GWR) |
| Housing Material | Aluminum, Stainless Steel |
| Measurement Type | Level |
| Process Pressure | Up to 40 bar (580 psi) |
| Output Signal | 4-20 mA HART |
| Communication Protocol | HART, FOUNDATION Fieldbus |
| Enclosure Rating | IP66 |
| Process Connection | Threaded, Flanged |
Crucial safety warnings and precautions for personnel.
Describes the content and structure of the manual.
Provides contact information and procedures for technical support.
Explains the Time Domain Reflectometry (TDR) measurement principle.
Details various uses of the Rosemount 3300 Series transmitter.
Identifies the physical parts and probe types of the transmitter.
Illustrates how the transmitter connects within a system.
Guidelines for choosing the appropriate probe for specific applications.
Explains upper and lower dead zones affecting the measurement range.
Discusses how coating, bridging, foam, and vapor affect measurements.
Details how probe type and application affect the measuring range.
Information on measuring liquid-to-liquid interfaces.
Covers mounting considerations related to tank features like agitators and shape.
Critical safety warnings and precautions for installation procedures.
Step-by-step guide for installing the transmitter correctly.
Pre-installation checks, including alarm and write protection switches.
Factors to consider for proper mounting, including connections and nozzles.
Procedures for physically mounting the transmitter head and probe.
Guidance on wiring, grounding, and cable selection for the transmitter.
To Next Page