Emerson TARTARINI FL Series - PED Categories and Fluid Group; Characteristics

Europe, Middle East, and Africa Only
Type FL
2
PED CATEGORIES AND FLUID GROUP
The FL series regulators without built-in safety slam-shut
devices (FL and MFL) may be used as a stand-alone safety
accessory in a fail-to-close conguration to protect pressure
equipment under the Pressure Equipment Directive 97/23/
EC categories.
The technical features of the downstream equipment,
protected by this regulator, should be classied under
a higher category according to the Pressure Equipment
Directive 97/23/EC.
According to EN 14382, only in an integral strength and
Class A type conguration (in both over and under pressure
protection congurations), can the possible built-in safety
slam-shut device (BFL) be classied as a safety accessory
according to P.E.D.
The minimum PS between slam-shut device and pilot shall
be the PS of the safety accessory, complying to EN 14382
for integral strength types.
The technical features of the downstream equipment,
protected by possible built-in safety slam-shut device
(conguration BFL Class A and integral strength) shall be
classied according to the Pressure Equipment Directive
97/23/EC, see table 1.
Table 1. P.E.D. Category for FL Series Regulators
PRODUCT SIZE CATEGORY FLUID GROUP
FL AND MFL TYPE
DN 25-40-50-65-80-100
150 (type FL or FL-BP only)
200 (type FL only)
IV 1
BFL TYPE
DN 25-40-50-65-80-100
The built-in pressure accessories (e.g. pilots OS/80X,
OS/80X-PN, PRX/, PS/, and V/31-1 series or lters
Type SA/2, FU/ and FD-GPL/) conform to Pressure
Equipment Directive (P.E.D.) 97/23/EC Article 3 Section
3 were designed and manufactured in accordance to the
Sound Engineering Practice (S.E.P.).
According to Article 3 Section 3, these “S.E.P.” products
must not bear the CE marking.
CHARACTERISTICS
Body Sizes and End Connection Styles
FL Series

DN 25 - 40 - 50 - 65 - 80 - 100 - 150
PN 16-25-40 UNI/ DIN
ANSI 150 anged

DN 25x100 - 40x150 - 50x150 - 65x200 - 80x250 - 100x250 - 150x300
PN 16-25-40 UNI/ DIN
ANSI 150 anged

DN 25 - 40 - 50 - 65 - 80 - 100 - 150 - 200
ANSI 300 - 600 anged

DN 25x100 - 40x150 - 50x150 - 65x200 - 80x250 - 100x250 - 150x300
- 200x400
ANSI 300 - 600 anged
BFL Series
BFL-BP
DN 25 - 40 - 50 - 65 - 80 - 100
PN 16-25-40 UNI/ DIN
ANSI 150 anged

DN 25x100 - 40x150 - 50x150 - 65x200 - 80x250 - 100x250
PN 16-25-40 UNI/ DIN
ANSI 150 anged
BFL
DN 25 - 40 - 50 - 65 - 80 - 100
ANSI 300 - 600 anged

DN 25x100 - 40x150 - 50x150 - 65x200 - 80x250 - 100x250
ANSI 300 - 600 anged
Maximum Operating Inlet Pressure
(1)(2)
PN 16: 16 bar
PN 25: 25 bar
ANSI 150: 20 bar
ANSI 300: 50 bar
ANSI 600: 100 bar
Outlet Set Pressure Ranges (Regulator)
PN 16 - ANSI 150: 0.01 to 8 bar
PN 25 - ANSI 300-600: 0.5 to 80 bar

0.03 to 80 bar

0.01 to 70 bar
!
WARNING