Emos EMP911 - Manual Control; Holiday Function

3
Do not use a normal pencil as the graphite could short circuit the
thermostat.
SETTING THE DAY AND TIME
1. Push the button to set hours, minutes and day.
2. Set the values by up/down arrows.
3. Navigate the menu by the button .
4. After setting the time, wait 15 minutes or push .
SETTING AND REGULATION OF TEMPERATURE
1. Use the button to switch the thermostat to the mode of Setting
and temperature control. The display will show a pictogram of the
set thermal mode (sun, moon) and the value will go ashing.
2. Push the thermal mode button (sun or moon) and use the up/down
arrow to set the required temperature.
3. The adjustable range of temperature is 5 to 30 °C. Conrm with the
.
MANUAL CONTROL
By pushing the up/down arrow, the display shows the “hand” pictogram,
i.e. manual control. A comfort or economy temperature set manually
will have precedence to any preset thermal mode, until the next pro-
grammed change arrives. You can cancel the priority of the manual con-
trol by pushing the SET button and the “hand” pictogram will disappear.
PROGRAMME SETTING AND CONTROL
1. Use the P button to show the present day programme on the screen.
2. Use the up/down arrow to change the day.
3. Then push P again to set the programme.
4. Use the
or to change the timing of the comfort and economy
temperature. A black eld means the comfort temperature, an
empty eld is the economy temperature. By the up/down arrow
you navigate through the daily times schedule.
5. By the button you conrm the changes and return to the normal
operating mode.
HOLIDAY FUNCTION
If needed, the thermostat allows setting one temperature for a longer
time period.
1. Hold the button and the temperature value will start ashing.
2. Push the up/down arrow to set the required temperature.
3. Conrm by the button. Now the icon appears. To cancel, push
again, and the suitcase icon will disappear.
RANGE OF THE SWITCH ON/OFF TEMPERATURE
The range is the dierence between the switch on and switch o
temperature. You can choose from 0.2 °C through 1.6 °C.
1. Push the S and use the up/down arrow to set the range value.
2. Conrm with .
Example: You set the temperature 22°C and a 0.5°C range, so the heating will
turn on, when the temperature drops below 21.5 °C and it turns o, when the
temperature exceeds 22.5 °C.
SETTING THE COOLING OR HEATING MODE – THE
DIP SWITCH
There is a DIP switch under the rear cover. It controls the toggling
between the cooling and heating system.
Because the comfort temperature for heating systems is generally
higher than the economy value and in case of cooling system it is on
the contrary, you need to toggle this switch to decide, if the thermostat
is to control a heating or a cooling system. Any mode change should
be done only when the power supply is disconnected and when the
batteries are not inserted!
Activated heating system – HEAT -
Activated cooling system – COOL -
COOLING SYSTEM CONTROL
The DIP switch allows using the thermostat also to control a cooling
system. The function is just like with the heating system, but there are
several dierences:
1. In general, the comfort temperature of a cooling system is lower
than the economy temperature value.
2. Switching on and o is reversed: the thermostat turns on, when the
temperature exceeds some set threshold.
This product is not designed to be used by persons (including children),
whose physical, sensory or mental incapacity or lack of experience
and knowledge prevents them from safe use of the appliance, unless
they are supervised or unless they have been instructed about the use
of this appliance by a person responsible for their safety. Supervision
over children is required to ensure they won’t play with the appliance.
After the end of the service life, do not throw the product or
batteries into unsorted communal waste. Use sorted waste
collecting points instead.
We declare responsibly, that the appliance marked as EMP911, its
concept and construction and its marketed version, complies with the
basic requirements and other relevant provision of the government
regulations. Any modications to the appliance unapproved by us
render this declaration invalid.
Rozměry: 125 x 84 x 29 mm (Š x V x H)
Baterie: 2 x1,5 V AA
Obsah balení
1. termostat
2. šrouby (2 ks)
3. hmoždinky (2 ks)
4. návod k obsluze
LCD displej
1. Teplota
2. Indikátor teplotního režimu, indikace chlazení nebo vytápění
3. Manuální ovládání
4. Funkce prázdniny
5. Indikátor průběhu programu
6. Indikátor slabých baterií – rozsvítí se, když napětí na bateriích klesne
pod určitou úroveň. Je nutné baterie co nejdříve vyměnit.
7. Čas
8. Den v týdnu
TERMOSTAT EMP911
Termostat EMP911 je regulátor teploty, který slouží ke kontrole a regulaci vytápěcích a chladicích systémů.
Před prvním použitím termostatu si pečlivě prostudujte tento návod.
CZ
• velký víceúčelový displej z tekutých krystalů (LCD)
• možnost řízení vytápěcího nebo chladícího systému
• program denovaný uživatelem
• 2 programy nastavení teploty
• manuálního ovládání
• nastavitelný rozptyl teploty
Technické parametry
Rozsah měření teploty: 0 – 40 °C (rozlišení 0,1 °C)
Rozsah řízení teploty: 5 – 30 °C (po 1 °C)
Přesnost teploty: ± 1 °C
Přesnost hodin: ±90 s za měsíc
Uživatelské programy: manuálně nastavený
Rozptyl zapínaní a vypínaní: 0,2°C až 1,6 °C (rozlišení 0,1 °C)
Provozní teplota: 5 – 40 °C
Skladovací teplota: 0 – 50 °C
Provozní vlhkost vzduchu: 0 – 90 %, nekondenzující
Spínání: 230 V~ 50 Hz
Maximální zatížení: 230 V, 6 A odporových, 2 A induktivních