Need help?Do you have a question about the Emotiva XPA-2 and is the answer not in the manual?
General| Frequency Response | 20 Hz to 20 kHz + / - 0.1 dB |
|---|---|
| Total Harmonic Distortion (THD) | < 0.1% |
| Number of Channels | 2 |
| Damping Factor | > 500 |
| Gain | 29 dB |
| Power Output (8 Ohms) | 300W |
| Signal to Noise Ratio (SNR) | >100dB |
| Input Sensitivity | 1.5V |
| Input Impedance | 23.5 kOhms |
Guidelines for grounding antenna systems to protect against voltage surges and lightning.
Details the key features and design elements of the Emotiva X Series amplifiers.
Explains the difference between peak and continuous power ratings in amplifiers.
Lists the items included with your Emotiva X Series amplifier.
Describes the function and status indications of the front panel LED display.
Explains the operation of the front panel power switch and standby mode.
Details the 5-way binding posts for connecting speakers and polarity.
Describes the selectors for controlling front panel status and meter LEDs.
Explains the 3.5mm trigger connection for remote power control.
Details the unbalanced RCA input for connecting preamplifiers or processors.
Switch to select between balanced XLR and unbalanced RCA inputs.
Details the balanced XLR input for connecting preamplifiers or processors.
Details the 5-way binding posts for connecting speakers and polarity.
Connection point for the amplifier's AC power cord.
The main rocker switch that controls the amplifier's primary power.
Indicates the detected operating voltage (115V or 230V).
Allows remote power control via a 3.5mm mono audio cable.
Selector to turn the channel status LEDs on or off.
Selector to turn the output meter LEDs on or off.
Balanced XLR input for the right audio channel.
Selects between RCA (Un-Bal) and XLR (Bal) input for the right channel.
Unbalanced RCA input for the right audio channel.
Enables bridging the two channels into a single monoblock amplifier.
Unbalanced RCA input for the left audio channel.
Selects between RCA (Un-Bal) and XLR (Bal) input for the left channel.
Balanced XLR input for the left audio channel.
Speaker terminals for the left channel, accepting various wire types.
Speaker terminals for the right channel, accepting various wire types.
Connection point for the amplifier's AC power cord.
Main power switch to turn the amplifier on/off.
Indicates the detected operating voltage (115V or 230V).
Selector to turn the channel status LEDs on or off.
Selects input type for Channel Three (RCA or XLR).
Unbalanced RCA input for the third audio channel.
Balanced XLR input for the third audio channel.
Selects input type for Channel Two (RCA or XLR).
Unbalanced RCA input for the second audio channel.
Balanced XLR input for the second audio channel.
Selects input type for Channel One (RCA or XLR).
Unbalanced RCA input for the first audio channel.
Balanced XLR input for the first audio channel.
Main power switch to turn the amplifier on/off.
Allows remote power control via a 3.5mm mono audio cable.
Speaker terminals for Channel Three.
Speaker terminals for Channel Two.
Speaker terminals for Channel One.
Connection point for the amplifier's AC power cord.
Indicates the detected operating voltage (115V or 230V).
Selector to turn the channel status LEDs on or off.
Selects input type for Channel Five (RCA or XLR).
Unbalanced RCA input for the fifth audio channel.
Balanced XLR input for the fifth audio channel.
Selects input type for Channel Four (RCA or XLR).
Unbalanced RCA input for the fourth audio channel.
Balanced XLR input for the fourth audio channel.
Selects input type for Channel Three (RCA or XLR).
Unbalanced RCA input for the third audio channel.
Balanced XLR input for the third audio channel.
Selects input type for Channel Two (RCA or XLR).
Unbalanced RCA input for the second audio channel.
Balanced XLR input for the second audio channel.
Selects input type for Channel One (RCA or XLR).
Unbalanced RCA input for the first audio channel.
Balanced XLR input for the first audio channel.
Main power switch to turn the amplifier on/off.
Allows remote power control via a 3.5mm mono audio cable.
Speaker terminals for Channel Five.
Speaker terminals for Channel Four.
Speaker terminals for Channel Three.
Speaker terminals for Channel Two.
Speaker terminals for Channel One.
Connection point for the amplifier's AC power cord.
Indicates the detected operating voltage (115V or 230V).
Guidance on electrical socket requirements and power distribution for the amplifier.
Information on the amplifier's built-in overcurrent, undercurrent, and spike protection.
Recommendations for optimal placement, ventilation, and heat management.
Recommendations for using high-quality, shielded RCA or XLR cables.
Details on standard binding post connectors and wiring precautions.
Advice on making connections for optimal audio performance and system setup.
Explains how to connect speakers in series, end-to-end, for impedance management.
Details connecting speakers in parallel, creating multiple paths for audio signals.
Important advice on using identical speakers for multi-speaker configurations.
Steps to diagnose and resolve issues where no audio is produced by speakers.
Troubleshooting steps for amplifier shutdowns or circuit breaker trips.
Diagnosing and fixing issues with weak or distorted bass response.
Methods to eliminate audible pops or thumps when powering the amplifier on/off.
Identifying and resolving unwanted hum or noise in the audio output.
Addresses additional potential sources of noise and interference.
Interpreting blinking red lights on the front panel indicating fault conditions.
Guidance for complex system-wide issues not solely related to the amplifier.
Detailed technical specifications for the Emotiva XPA-1 amplifier.
Detailed technical specifications for the Emotiva XPA-2 amplifier.
Detailed technical specifications for the Emotiva XPA-3 amplifier.
Detailed technical specifications for the Emotiva XPA-5 amplifier.
Instructions for obtaining repair services, including RMA procedures.
To Next Page
