How to resolve communication error on Emotron FDU40-003 Servo Drives?
A communication error in Emotron Servo Drives indicates an issue with serial communication. Check the cables and connections, verify all serial communication settings, and restart the equipment, including the VSD.
What causes pump error in Emotron FDU40-003 Servo Drives?
If your Emotron Servo Drives display a pump error, no master pump can be selected due to an error in feedback signaling. Check the cables and wiring for pump feedback signals and verify the settings related to the pump feedback digital inputs.
What does Mon MinAlarm mean on Emotron Servo Drives?
If your Emotron Servo Drives display a 'Mon MinAlarm', the minimum alarm level (underload) has been reached. Check the load condition of the machine.
What causes Mon MaxAlarm on Emotron Servo Drives?
If your Emotron Servo Drives are triggering a 'Mon MaxAlarm', the maximum alarm level (overload) has been reached. Check the load condition of the machine.
What to check if Emotron FDU40-003 show Ext Mot Temp error?
If your Emotron Servo Drives display 'Ext Mot Temp', an external input (DigIn 1-8) is active, potentially due to an active low function on the input. Check the equipment that triggers the external input and verify the programming of the digital inputs DigIn 1-8.
What does Ext trip mean on Emotron FDU40-003 Servo Drives?
If your Emotron Servo Drives are showing an external trip, it means an external input (DigIn 1-8) is active, possibly due to an active low function on the input. Check the equipment initiating the external input and verify the programming of the digital inputs DigIn 1-8.
How to fix PT100 error on Emotron FDU40-003 Servo Drives?
If your Emotron Servo Drives display a PT100 error, it indicates that the motor PT100 elements have exceeded the maximum level. Check for mechanical overload on the motor or machinery and inspect the motor cooling system. Ensure that a self-cooled motor is not under too high a load at low speed. You can also set PT100 to OFF.
What does PTC error mean on Emotron Emotron Servo Drives?
If your Emotron Servo Drives are showing a PTC error, the motor thermistor (PTC) has exceeded its maximum level. Check for mechanical overload on the motor or machinery, inspect the motor cooling system, and ensure a self-cooled motor isn't under too high a load at low speed. You can also set PTC to OFF.
What does motor I2t error mean on Emotron FDU40-003?
The 'Motor I2t' error in Emotron Servo Drives means the I2t value has been exceeded, indicating an overload on the motor based on programmed I2t settings. Check for mechanical overloads on the motor or machinery, such as issues with bearings, gearboxes, chains, or belts. You might also need to adjust the 'Motor I2t Current' setting.
What to do if Emotron FDU40-003 Servo Drives show over current fault?
If the motor current exceeds the peak VSD current in your Emotron Servo Drives, it could be due to several reasons. You might have too short acceleration time, excessive load change, or even a soft short-circuit. Check the acceleration time settings, motor load, motor cable connections, earth cable connection, and for any moisture in the motor housing. Also, consider lowering the level of IxR Compensation.
Guidelines for installation, commissioning, and demounting.
Precautions to take before opening the unit, especially regarding capacitors.
Ensuring compliance with EMC Directive for installation.
Details on connecting motor cables, including screening and selection.
Using parameter sets to configure different operating modes and settings.
Compliance with EMC standards EN(IEC)61800-3.
Information on EN 60204-1 stop categories and emergency stop functions.
Functions to protect the motor against overload based on standard IEC 60947-4-2.
Using the PID controller to manage external processes via feedback signals.
Functions to monitor load and protect machinery against overload.
Overview of system monitoring and how variables exceeding safety limits trigger actions.
A guide to identifying causes of system failures and their solutions.
Configuration for Safe Stop according to EN954-1 Category 3.
General| Rated Motor Power | 3 kW |
|---|---|
| Rated Current | 7.2 A |
| IP Rating | IP20 |
| Output Current | 7.2 A |
| Control Type | Vector Control |
| Rated Supply Voltage | 380-480 V |
| Input Voltage | 380-480 V |
| Communication Interface | Modbus |
To Next Page
