EasyManuals Logo

EMPHASER EA285 User Manual

EMPHASER EA285
17 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #6 background imageLoading...
Page #6 background image
10 11
2. CONNECTIONS + TOP CONTROLS EA1300
2.1 INPUTS + OUTPUTS
1 CINCH MASTER / SLAVE IN-OUT
Master Slave RCA sockets to connect at least two EA1300 amps in Master / Slave
mode. Master / Slave mode allows to drive one amp with RCA input signal from the
head unit, and to daisy chain all further amps of the system.
To connect in Master / Slave mode, a mono RCA interconnect cable is required. See
connection drawing on page 28.
2 RCA INPUTS 1/2-CH
Low-level stereo RCA signal input 1/2-CH for connection to head-unit.
3 REMOTE CONTROL INPUT
Input terminal to connect the external bass level remote to the amplifier.
4 HIGH INPUT
Molex connector terminal to insert the High level adapter (4-Pin) that picks up the
amplified speaker signals from the head unit’s front and rear outputs (if head unit
does not feature dedicated RCA line outs).
5 SPEAKER OUTPUT TERMINAL
Output terminal to connect the speakers to the amplifier in either stereo or bridged
mode. For bridge connection, use the terminals with fat polarity signs.
6 ATC FUSE HOLDER
Fuse holder for 2 x 25 A ATC fuses. Never deploy fuses of higher amperage rating.
7 “+12 V” POWER INPUT TERMINAL
Terminal to connect the amplifier to the positive +12 V pole of the car battery.
8 “REM” INPUT TERMINAL
Terminal to connect the amplifier to the automatic (remote) turn-on / turn-off lead of
the head unit.
9 “GND” POWER INPUT TERMINAL
Terminal to connect the amplifier to the chassis ground or negative pole of the car
battery.
976
2.2 TOP CONTROLS
1 INPUT GAIN CONTROL CH1/CH2
Input gain potentiometer for channel CH1/CH2, to match the output voltage of the
head-unit to the amplifier’s input.
2 PHASE SWITCH CH1/CH2
Switch to select normal or inverted phase for section CH1/CH2 of the amplifier.
3 X-OVER FREQUENCY CONTROL CH1/CH2
Control potentiometer to adjust the lowpass filtering frequency point for section
CH1/CH2 of the amplifier.
4 SUBSONIC HIGHPASS FREQUENCY CONTROL
Control potentiometer to adjust the subsonic highpass filtering frequency point for
section CH1/CH2 of the amplifier.
5 POWER LED
LED bar segment to show “operating” status of the amplifier by red illumination.
Protect state of amplifier is signaled by blue state.
1
4
5
GAIN
LPF
MIN MAX
40Hz 250Hz
SUB
SONIC
15Hz 50Hz
:
:
RECEN B ES T EL ECTR ON IC FA CTORY
:
RM P -GT3 0 0
<5
5~1 0
10~1 00
>10 0
:
:
:
: 2 0 1 3 . 7 . 9
1/1
MM
+0.1
+0.2
+0.5
+1.0
-
-
-
-
:
1.
PHASE
180°
:
:
RECEN B ES T EL ECTR ON IC FA CTORY
:
RM P -GT3 0 0
<5
5~1 0
10~1 00
>10 0
:
:
:
: 2 0 1 3 . 7 . 9
1/1
MM
+0.1
+0.2
+0.5
+1.0
-
-
-
-
:
1.
2 3
:
:
RECEN B ES T EL ECTR ON IC FA CTORY
:
RM P -GT3 0 0
<5
5 ~1 0
1 0 ~1 0 0
>1 0 0
:
:
:
: 2 0 1 3 . 7 . 9
1/ 1
MM
+0 . 1
+0 . 2
+0 . 5
+1 . 0
-
-
-
-
:
1.
INPUT
IN
OUT
MASTER/SLAVE
REM
CH1
CH2
FUSES
GND
REM
12V
HIGH INPUT
E A1300
:
:
RECEN B ES T EL ECTR ON IC FA CTORY
:
RM P -GT3 0 0
<5
5 ~1 0
1 0 ~1 0 0
>1 0 0
:
:
:
: 2 0 1 3 . 7 . 9
1/ 1
MM
+0 . 1
+0 . 2
+0 . 5
+1 . 0
-
-
-
-
:
1.
INPUT
IN
OUT
MASTER/SLAVE
REM
CH1
CH2
FUSES
GND
REM
12V
HIGH INPUT
E A1300
3 5 81 2 4
25 A
25 A
:
:
RE C EN BES T EL E CT R ON I C FA C TO RY
:
RMP - G T30 0
<5
5~ 1 0
10 ~ 10 0
>1 0 0
:
:
:
:2013. 7 . 9
1/1
MM
+0 . 1
+0 . 2
+0 . 5
+1 . 0
-
-
-
-
:
1.
INP U T
IN
OUT
BRIDGE
REM
CH1
CH2
SP E AK E R O UTPU T
FUSES
POWER INPUT
GND
REM
12V
Ch1+
Ch1-
Ch2+
Ch2-
HIGH INPUT
25Ax2
EA1300
HIGH INPUT

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the EMPHASER EA285 and is the answer not in the manual?

EMPHASER EA285 Specifications

General IconGeneral
BrandEMPHASER
ModelEA285
CategoryAmplifier
LanguageEnglish

Related product manuals