16 17
2- Flushing
1 2 3 4
H
2
O
Place the water bottle fully
filled.
Set water to 10.
Turn the device ON.
Hold cord over a sink.
Press the pedal until the water
runs clear.
To reduce the risk of
ingestion of the cleaning
agent by the patient, always
use a fully filled 800ml
water bottle.
Set water regulator to 10 to
ensure optimal rinsing.
Contamination prevention:
DO NOT make any contact
between the sink and the
cords.
Cleaning can be paused and
reset by pressing the pedal
again.
Remove the water bottle and
rinse well prior to filling with
water for the first patient of the
day.
DO NOT leave water in your water bottles overnight. Allow the bottles to air with the lids off overnight.
Always empty out and wash the water bottle used for rinsing before any new use. EMS recommends a weekly use of a bottle
cleaning agent.
After every patient
Overall cleaning and disinfection
1 2
Use a cleaning and disinfecting wipe (less than 35% alcohol) compatible EPA-
registered intermediate level surface disinfectant or that complies with the standards
applicable in the country (e.g. MICROKLEEN or Opti-Cide³ wipes).
Follow carefully the instructions provided by the wipes manufacturer.
DO NOT use CaviWipes™ or Advantaclear wipes. They damage EMS products
Reprocess handpieces and
instruments. Please refer to FB-
358/NA “reprocessing instructions”
delivered with your kit.
Risk of contamination. Always
disinfect the bottom and top areas of
device air connections.
Please remember to dry your
AIRFLOW
®
cord connection and ensure
it is cooled and dried prior to each use.
Excess moisture can cause blockages.
III CLEANING AND REPROCESSING
Follow the recommendations of the "Reprocessing Instructions" (FB-358/NA) manual delivered with your product
regarding procedure for cleaning and sterilizing the components, and the present-day regulations on reprocessing in effect in
your country.
Reusable Products:
Description
AIRFLOW
®
MAX handpiece CLIP+CLEAN
PERIOFLOW
®
handpiece Easy Clean
3.1- Water lines cleaning & disinfection
If you have the AIRFLOW
®
STATION+, bottle has to be placed onto the cart to run the lines. To disinfect the
unit place the CLEANER bottle on the bottom only.
NIGHT
CLEANER
WATER SUPPLY
BY HOSE EG-110
Keeping the device’s water lines clean and disinfected is mandatory to prevent patient infection.
A regular cleaning and maintenance protocol should be adopted to clean and protect dental unit
waterlines. EMS recommends using EPA-registered dental unit waterline cleaners, VistaCleanTM
Irrigant Solution Concentrate and VistaTab™ Dental Unit Waterline Cleaner by Hu-Friedy or
Monarch Lines Cleaner by Air Techniques.
Follow the instructions for use of the product.
The instructions for use should be followed to ensure the appropriate water quality to help protect
patients, staff and equipment.
Handpiece should be removed prior to using VistaCleanTM /VistaTab™ or Monarch Lines
Cleaner.
The water supply hose and related device connection will not be cleaned by this procedure.
Initial start-up treatment and routine treatment
Follow the instructions for use of the product.
For daily water line disinfection: Add drops
16
of VistaCleanTM Irrigant Solution Concentrate in the water bottle fully filled (800ml)
and use it with patients.
Dental unit waterline cleaner and AIRFLOW
®
ONE
1- Waterlines cleaning with VistaTab™ Dental Unit Waterline Cleaner or Monarch Lines Cleaner.
Follow the instructions for use of the product.
1 2 3 4
CLEANER
Place the CLEANER bottle onto
the device with VistaTab™ or
Monarch Lines Cleaner
Set water to 10.
Turn the device ON.
Hold cord over a sink.
Press the pedal once,
release, and wait 1 minute.
Repeat if necessary until the
solution is visible.
Set water regulator to 10 to
ensure the flow of the cleaning
agent.
Contamination prevention:
DO NOT make any contact
between the sink and the
cords.
16 Follow disinfection products manufacturer instructions. Please refer to your public health guidelines.
Scan
for
support
To Next Page
Loading...
Need help?
General
