To Next PageTo Next Page
How to fix the wrong slope of the measured interface level in Endress+Hauser Measuring Instruments?
The wrong slope of the measured interface level is caused by the wrong dielectric constant (DC value). To correct this, enter the correct dielectric constant (DC value) of the upper medium.
Why Endress+Hauser Radar device does not respond?
If your Endress+Hauser Radar device isn't responding, it could be due to a couple of reasons: * The supply voltage might not be correctly connected; ensure you connect the correct voltage. * The cables might not be making proper contact with the terminals; make sure there's good electrical contact between the cable and the terminal.
What to do if Endress+Hauser Radar device measures incorrectly?
If your Endress+Hauser Radar device is providing incorrect measurements, the cause could be a parameterization error. To solve this, check and adjust the parameterization of the device.
What to do if values on Endress+Hauser Radar display are invisible?
If the values on your Endress+Hauser Radar's display are invisible, here are a few things to check: * The contrast setting might be too weak or too strong. Try increasing the contrast by pressing the indicated buttons simultaneously or decreasing it in the same way. * The display cable plug might not be connected correctly; ensure it is properly connected. * The display itself might be defective, in which case you should replace it.
Why does the measured total level jump to lower values during filling when 'Partially filled' is selected in 'Tank level' on Endress+Hauser Levelflex FMP51 Measuring Instruments?
If, when 'Partially filled' is selected in 'Tank level', the measured total level jumps to lower values during filling operations, the total level may be running into the upper blocking distance. To resolve this, reduce the blocking distance.
Why the measured values for the interface and the total level are identical in Endress+Hauser Levelflex FMP51?
The measured values for the interface and the total level can be identical if the echo threshold for the total level is too high due to a wrong dielectric constant. To solve this, enter the correct dielectric constant (DC value) of the upper medium.
What causes the measured interface level to jump to higher values during draining when 'flooded' is selected in 'Tank level' on Endress+Hauser Levelflex FMP51?
If, when 'flooded' is selected in 'Tank level', the measured interface level jumps to higher values during draining operations, a possible cause is that the total level is detected outside the upper blocking distance. To address this, increase the blocking distance. Alternatively, select 'Tank level' = 'Partially filled'.
Why CDI communication is not working on Endress+Hauser Radar?
If CDI communication does not work with your Endress+Hauser Radar, the COM port setting on your computer may be incorrect. Check the COM port setting and change it if necessary.
How to troubleshoot an Endress+Hauser Radar device that does not respond?
If the Endress+Hauser Radar device does not respond, it could be due to the following reasons: * The supply voltage is not connected. Connect the correct voltage. * The cables do not contact the terminals properly. Ensure electrical contact between the cable and the terminal.
How to fix invisible values on Endress+Hauser Radar display?
If the values on the display of your Endress+Hauser Radar are invisible, the contrast setting may be too weak or too strong. Try these steps: * Increase the contrast by pressing the designated buttons simultaneously. * Decrease the contrast by pressing the designated buttons simultaneously. Alternatively, the display cable plug might not be connected correctly, so ensure it is properly connected. If the issue persists, the display may be defective and require replacement.
General| Device Type | Guided radar level transmitter |
|---|---|
| Application | Level measurement for liquids and solids |
| Measuring Range | Up to 30 m |
| Process Temperature | -40 to 200 °C (-40 to 392 °F) |
| Process Pressure | -1 to +40 bar (-14.5 to +580 psi) |
| Output Signal | 4-20 mA HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Housing Material | Aluminum, Stainless steel |
| Probe Type | Rod or cable |
| Material | Stainless steel, PTFE |
| Protection Rating | IP66/IP67 |
| Approvals | ATEX, IECEx, FM, CSA |
| Power Supply | 10.5 to 36 V DC |
