Why does the measured total level jump to lower values during filling when 'Partially filled' is selected in 'Tank level' on Endress+Hauser Measuring Instruments?
If, when 'Partially filled' is selected in 'Tank level', the measured total level jumps to lower values during filling operations, the total level may be running into the upper blocking distance. To resolve this, reduce the blocking distance.
How to fix the wrong slope of the measured interface level in Endress+Hauser Measuring Instruments?
The wrong slope of the measured interface level is caused by the wrong dielectric constant (DC value). To correct this, enter the correct dielectric constant (DC value) of the upper medium.
Why Endress+Hauser Radar device does not respond?
If your Endress+Hauser Radar device isn't responding, it could be due to a couple of reasons: * The supply voltage might not be correctly connected; ensure you connect the correct voltage. * The cables might not be making proper contact with the terminals; make sure there's good electrical contact between the cable and the terminal.
Why is there a wrong slope of the measured interface level in my Endress+Hauser Levelflex FMP54 Measuring Instruments?
If there is a wrong slope of the measured interface level in your Endress+Hauser Measuring Instruments, the dielectric constant (DC value) may be incorrect. Enter the correct dielectric constant (DC value) of the upper medium.
What to do if my Endress+Hauser Measuring Instruments device does not respond?
If your Endress+Hauser Measuring Instruments device isn't responding, there are a couple of things to check: * First, make sure the supply voltage is correctly connected. If it is not, connect the correct voltage. * Second, verify that the cables are making proper contact with the terminals. Ensure electrical contact between the cable and the terminal.
What to do if the values on my Endress+Hauser Measuring Instruments display are invisible?
If the values on your Endress+Hauser Measuring Instruments display are not visible: * The contrast setting may be too weak or too strong. Increase contrast by pressing the indicated buttons simultaneously or decrease contrast by pressing the indicated buttons simultaneously. * The plug of the display cable might not be connected correctly. Connect the plug correctly. * The display itself could be defective. Replace the display.
Why is the output current less than 3.6 mA on my Endress+Hauser Radar?
If the output current is less than 3.6 mA on your Endress+Hauser Radar device: * Check the signal cable connection to ensure it is correct. * Replace the electronics, as the electronics might be defective.
Why CDI communication does not work for Endress+Hauser Radar?
If CDI communication does not work with your Endress+Hauser Radar, the COM port on the computer might be set incorrectly. Check the setting of the COM port on the computer and change it if necessary.
What to do if with the setting Tank level = Partially filled, the measured total level jumps to lower values during filling operations in Endress+Hauser Measuring Instruments?
If, with the setting Tank level = Partially filled, the measured total level jumps to lower values during filling operations in your Endress+Hauser Measuring Instruments, the total level might be running into the upper blocking distance. Decrease the blocking distance.
How to troubleshoot an Endress+Hauser Radar device that does not respond?
If the Endress+Hauser Radar device does not respond, it could be due to the following reasons: * The supply voltage is not connected. Connect the correct voltage. * The cables do not contact the terminals properly. Ensure electrical contact between the cable and the terminal.
Outlines necessary qualifications for personnel.
Specifies intended application and materials.
Details safety measures for working with the device.
Covers safe operation, conversions, and repairs.
Covers general requirements and suitable positions.
Details tensile and bending strength limits.
Discusses threaded connections and seals.
Details mounting instructions for cladded flanges.
Covers securing rope probes.
Details probe rod mounting for FMP54 with GPC.
Covers device mounting with thread and flange.
Details mounting for remote sensor versions.
Lists final checks after installation.
Details terminal assignment and cable specifications.
Provides details on cable types and specifications.
Details power supply requirements for different approvals.
Step-by-step guide for connecting the device.
Lists checks after connecting the device.
Guides on configuring blocks for operation.
Step-by-step guide for configuring level measurement.
Guide for configuring interface measurements.
Provides solutions for common device issues.
Guides on accessing remedial measures for diagnostic events.
Details parameters within the Setup menu.
Outlines diagnostic functions and messages.
General| Measuring Principle | TDR (Time Domain Reflectometry) |
|---|---|
| Measuring Range | Up to 30 m |
| Output | 4-20 mA HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Power Supply | 10.5 to 36 V DC (two-wire) |
| Housing Material | Aluminum, Stainless Steel |
| Process Connection | Thread, Flange |
| Approvals | ATEX, IECEx |
| Material | PTFE |
| Protection Class | IP66/IP67 |
To Next Page