Why do the measured values for the interface and the total level are identical in my Endress+Hauser Levelflex FMP54 Measuring Instruments?
If the measured values for the interface and the total level are identical in your Endress+Hauser Measuring Instruments, the echo threshold for the total level might be too high due to a wrong dielectric constant. Enter the correct dielectric constant (DC value) of the upper medium.
What to do if with the setting Tank level = Fully floodedWhen, the measured interface level jumps to higher values during draining operations in Endress+Hauser Levelflex FMP54?
If, with the setting Tank level = Fully floodedWhen, the measured interface level jumps to higher values during draining operations in your Endress+Hauser Measuring Instruments: * The total level is detected outside the upper blocking distance. Increase the blocking distance. * Set Tank level parameter to Partially filled.
What to do if with the setting Tank level = Partially filled, the measured total level jumps to lower values during filling operations in Endress+Hauser Measuring Instruments?
If, with the setting Tank level = Partially filled, the measured total level jumps to lower values during filling operations in your Endress+Hauser Measuring Instruments, the total level might be running into the upper blocking distance. Decrease the blocking distance.
Why CDI communication is not working on Endress+Hauser Radar?
If CDI communication does not work with your Endress+Hauser Radar, the COM port setting on your computer may be incorrect. Check the COM port setting and change it if necessary.
How to fix the wrong slope of the measured interface level in Endress+Hauser Measuring Instruments?
The wrong slope of the measured interface level is caused by the wrong dielectric constant (DC value). To correct this, enter the correct dielectric constant (DC value) of the upper medium.
Why Endress+Hauser Radar device does not respond?
If your Endress+Hauser Radar device isn't responding, it could be due to a couple of reasons: * The supply voltage might not be correctly connected; ensure you connect the correct voltage. * The cables might not be making proper contact with the terminals; make sure there's good electrical contact between the cable and the terminal.
What to do if Endress+Hauser Radar device measures incorrectly?
If your Endress+Hauser Radar device is providing incorrect measurements, the cause could be a parameterization error. To solve this, check and adjust the parameterization of the device.
What to do if values on Endress+Hauser Radar display are invisible?
If the values on your Endress+Hauser Radar's display are invisible, here are a few things to check: * The contrast setting might be too weak or too strong. Try increasing the contrast by pressing the indicated buttons simultaneously or decreasing it in the same way. * The display cable plug might not be connected correctly; ensure it is properly connected. * The display itself might be defective, in which case you should replace it.
What to do if "Communication error" is indicated on the Endress+Hauser Radar display?
If you see a "Communication error" message on the display of your Endress+Hauser Radar when starting the device or connecting the display, it could be due to: * Electromagnetic interference. Check the grounding of the device. * A broken display cable or display plug. In this case, replace the display.
How to fix CDI communication error on Endress+Hauser Radar?
If CDI communication isn't working on your Endress+Hauser Radar, the COM port setting on your computer may be incorrect. Check the COM port setting and change it if necessary.
Outlines necessary qualifications for personnel.
Specifies intended application and materials.
Details safety measures for working with the device.
Covers safe operation, conversions, and repairs.
Covers general requirements and suitable positions.
Details tensile and bending strength limits.
Discusses threaded connections and seals.
Details mounting instructions for cladded flanges.
Covers securing rope probes.
Details probe rod mounting for FMP54 with GPC.
Covers device mounting with thread and flange.
Details mounting for remote sensor versions.
Lists final checks after installation.
Details terminal assignment and cable specifications.
Provides details on cable types and specifications.
Details power supply requirements for different approvals.
Step-by-step guide for connecting the device.
Lists checks after connecting the device.
Guides on configuring blocks for operation.
Step-by-step guide for configuring level measurement.
Guide for configuring interface measurements.
Provides solutions for common device issues.
Guides on accessing remedial measures for diagnostic events.
Details parameters within the Setup menu.
Outlines diagnostic functions and messages.
General| Measuring Principle | TDR (Time Domain Reflectometry) |
|---|---|
| Measuring Range | Up to 30 m |
| Output | 4-20 mA HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Power Supply | 10.5 to 36 V DC (two-wire) |
| Housing Material | Aluminum, Stainless Steel |
| Process Connection | Thread, Flange |
| Approvals | ATEX, IECEx |
| Material | PTFE |
| Protection Class | IP66/IP67 |
To Next Page