Why is my Endress+Hauser Radar measuring incorrectly?
If your Endress+Hauser Radar device is measuring incorrectly, it might be due to a parameter configuration error. Review the parameter configuration and correct any mistakes.
What to do if Endress+Hauser Radar displays a communication error?
If the display shows 'Communication error' when starting the device or connecting the display on your Endress+Hauser Radar, the issue may be electromagnetic interference. Check the grounding of the device. Alternatively, the display cable or plug might be broken, in which case you should replace the display.
How to troubleshoot an Endress+Hauser Radar device that does not respond?
If the Endress+Hauser Radar device does not respond, it could be due to the following reasons: * The supply voltage is not connected. Connect the correct voltage. * The cables do not contact the terminals properly. Ensure electrical contact between the cable and the terminal.
How to fix invisible values on Endress+Hauser Radar display?
If the values on the display of your Endress+Hauser Radar are invisible, the contrast setting may be too weak or too strong. Try these steps: * Increase the contrast by pressing the designated buttons simultaneously. * Decrease the contrast by pressing the designated buttons simultaneously. Alternatively, the display cable plug might not be connected correctly, so ensure it is properly connected. If the issue persists, the display may be defective and require replacement.
How to correct wrong slope of the level in the entire measuring range in Endress+Hauser Levelflex FMP54?
The wrong slope of the level in the entire measuring range could be caused by the wrong tank type being selected. To fix this, set the Tank type parameter correctly.
What to do if parameter duplication is not working on Endress+Hauser Radar?
If the duplication of parameters via display from one device to another is not working on your Endress+Hauser Radar and only the 'Save' and 'Cancel' options are available, it could be because the display with backup is not properly detected if a data backup was not carried out on the new device previously. Connect the display (with backup) and restart the device.
Why is my Endress+Hauser Radar device measuring incorrectly?
If the Endress+Hauser Radar device measures incorrectly, it might be due to a parametrization error. Check and adjust the parameterization to resolve this issue.
What to do if my Endress+Hauser Radar device does not respond?
If the Endress+Hauser Radar device does not respond, verify the following: * Ensure the supply voltage matches the value indicated on the nameplate and connect the correct voltage if it doesn't. * Correct the polarity if the supply voltage polarity is wrong. * Ensure proper electrical contact between the cables and terminals.
Why is HART communication not functioning on my Endress+Hauser Radar?
If HART communication does not function on your Endress+Hauser Radar, consider the following: 1. Install the communication resistor (250 ?) correctly if it is missing or incorrectly installed. 2. Connect the Commubox correctly. 3. Set the selection switch of the Commubox to the HART position.
What to do if Endress+Hauser Radar displays 'Communication error'?
If a "Communication error" is indicated on the display of your Endress+Hauser Radar, when starting the device or connecting the display: * Check the grounding of the device, as electromagnetic interference could be the cause. * Exchange the display, because the display cable or display plug could be broken.
Outlines necessary qualifications for personnel.
Specifies intended application and materials.
Details safety measures for working with the device.
Covers safe operation, conversions, and repairs.
Covers general requirements and suitable positions.
Details tensile and bending strength limits.
Discusses threaded connections and seals.
Details mounting instructions for cladded flanges.
Covers securing rope probes.
Details probe rod mounting for FMP54 with GPC.
Covers device mounting with thread and flange.
Details mounting for remote sensor versions.
Lists final checks after installation.
Details terminal assignment and cable specifications.
Provides details on cable types and specifications.
Details power supply requirements for different approvals.
Step-by-step guide for connecting the device.
Lists checks after connecting the device.
Guides on configuring blocks for operation.
Step-by-step guide for configuring level measurement.
Guide for configuring interface measurements.
Provides solutions for common device issues.
Guides on accessing remedial measures for diagnostic events.
Details parameters within the Setup menu.
Outlines diagnostic functions and messages.
General| Measuring Principle | TDR (Time Domain Reflectometry) |
|---|---|
| Measuring Range | Up to 30 m |
| Output | 4-20 mA HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Power Supply | 10.5 to 36 V DC (two-wire) |
| Housing Material | Aluminum, Stainless Steel |
| Process Connection | Thread, Flange |
| Approvals | ATEX, IECEx |
| Material | PTFE |
| Protection Class | IP66/IP67 |
To Next Page