To Next PageTo Next PageWhat to do if the Endress+Hauser Proline Prowirl F 200 Measuring Instruments device measures incorrectly?
If your Endress+Hauser Measuring Instruments device is measuring incorrectly, you should first check and correct the parameter configuration. Also, make sure to observe the limit values specified in the Technical Data.
How to fix dark local display and no output signals on Endress+Hauser Proline Prowirl F 200?
If the local display is dark and there are no output signals on your Endress+Hauser Measuring Instruments, consider the following: * Ensure the supply voltage matches the value on the nameplate; if it doesn't, apply the correct supply voltage. * Verify the polarity of the supply voltage and correct it if wrong. * Check the connection of the cables and correct if necessary. * Check terminals if they are plugged into the I/O electronics module correctly. * If the I/O electronics module is defective, order a spare part.
Why is the Endress+Hauser Proline Prowirl F 200 Measuring Instruments device showing the correct value on the local display, but the signal output is incorrect?
If your Endress+Hauser Measuring Instruments device shows the correct value on the local display, but the signal output is incorrect, it may be due to a configuration error. Check and correct the parameter configuration.
What to do if the Endress+Hauser Proline Prowirl F 200 Measuring Instruments local display is dark but signal output is within the valid range?
If the local display on your Endress+Hauser Measuring Instruments is dark, but the signal output is within the valid range: * The display may be set too bright or too dark. Set the display brighter by simultaneously pressing the appropriate buttons. Set the display darker by simultaneously pressing the appropriate buttons. * Check that the cable of the display module is correctly inserted into the main electronics module and display module. * If the display module is defective, consider ordering a spare part.
How to restore write access to parameters on Endress+Hauser Proline Prowirl F 200?
If you have no write access to parameters on your Endress+Hauser Measuring Instruments: 1. Check if hardware write protection is enabled and set the write protection switch on the main electronics module to the OFF position. 2. Verify the current user role and access code. Check user role and enter the correct customer-specific access code.
Why is the backlighting of local display red on Endress+Hauser Measuring Instruments?
The red backlighting on the local display of your Endress+Hauser Measuring Instruments indicates that a diagnostic event with an "Alarm" diagnostic behavior has occurred. Take remedial measures.
What does "Communication Error" on Endress+Hauser Measuring Instruments mean?
If the message "Communication Error" "Check Electronics" appears on the local display of your Endress+Hauser Measuring Instruments, it means that communication between the display module and the electronics is interrupted. Check the cable and the connector between the main electronics module and display module. If needed, order a spare part.
How to change the language on Endress+Hauser Measuring Instruments?
If the text on the local display of your Endress+Hauser Measuring Instruments appears in a foreign language, follow these steps: 1. Press the appropriate buttons for 2 seconds to reach the "home position". 2. Press the indicated button. 3. Set the desired language in the Language parameter.
General| Device Type | Vortex flowmeter |
|---|---|
| Process temperature | -200 to +400 °C (-328 to +752 °F) |
| Measured variables | Mass flow, Density, Temperature |
| Nominal diameter | DN 15 to 300 (½ to 12") |
| Wetted materials | Stainless steel, Hastelloy |
| Output | 4-20 mA, Frequency, Pulse |
| Communication | HART, PROFIBUS, FOUNDATION Fieldbus |
| Ingress protection | IP66/67 |
| Approvals | ATEX, FM, CSA, IECEx |
| Process Connection | Flanged, threaded |
| Material | Stainless steel |
| Accuracy | ±0.75% of reading (liquid), ±1% of reading (gas/steam) |
| Repeatability | ±0.2% of reading |
| Measurement Principle | Vortex shedding principle |
